Canandaigua soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 8 to 30 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Canandaigua soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Canandaigua spot on the map
Rated from the USDA soil survey record for Canandaigua silt loam (Addison County, Vermont) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 27% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (10).
- Note Thick enough to investigate (about 22 in (56 cm)).
- Note Typically starts within about 8 in (20 cm) of the surface.
- Note Few rock fragments (about 4% by volume).
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 8 in down: about 27% clay, moderate plasticity when wet, very dark gray when moist. Possible
- Loamy layerH2best layer A silt loam layer about 8 to 30 in down: about 27% clay, moderate plasticity when wet, light brownish gray when moist. Possible
- Loamy layerH3 A silt loam layer about 30 to 72 in down: about 27% clay, low plasticity when wet, gray when moist. Weak indication
What it looks like raw
The loamy layer (H2), 8 to 30 in down in the typical profile: light brownish gray (10YR 6/2); friable. Raw colour is not fired colour.
About the soil
- Parent material: fine-silty glaciolacustrine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 2 map units in New York, Vermont, in these survey areas: Addison County, Vermont; Otsego County, New York.
By state: wild clay in New York,wild clay in Vermont.
USDA, distribution and extent: New York, Pennsylvania, and Vermont. MLRA 101, 139, 140, 142, and 144A. The series is of large extent.
USDA, geographic setting: Canandaigua soils are nearly level soils mainly on glacial lake plains, but are also in depressional areas of glaciated uplands where water-sorted sediments have accumulated to a depth of more than 100 centimeters. Slope is mainly less than 1 percent, but ranges up to 3 percent. Mean annual temperature ranges from 7.5 degrees to 11.5 degrees C.; mean frost-free season ranges from 140 to 200 days; and mean annual precipitation ranges from 715 to 1270 millimeters. The elevation commonly ranges from 30 to 396 meters but the range includes up to 533 meters above sea level.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Covington: Strong lead
- Livingston: Strong lead
- Melrose: Strong lead
- Swanton: Strong lead
- Vergennes: Strong lead
- Elmwood: Promising
- Alden: Possible
- Farmington: Possible
See it on the map
Open a Canandaigua spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Canandaigua silt loam, map unit Cn in Addison County, Vermont.
- Official Series Description: Canandaigua(revised 04/2025), established.
- Taxonomic class: Fine-silty, mixed, active, nonacid, mesic Mollic Endoaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.