Machias soil
Wild-clay potential
Weak indication
Weak indication: no layer of Machias shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Machias soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Machias spot on the map
Rated from the USDA soil survey record for Machias fine sandy loam, 0 to 3 percent slopes (Washington County, Vermont) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 43 in (109 cm)).
- Note Typically starts within about 22 in (56 cm) of the surface.
- Lowers the potential High rock content (about 47% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 8 in down: about 9% clay, low plasticity when wet, dark yellowish brown when moist. Weak indication
- Sandy layerH2 A fine sandy loam layer about 8 to 22 in down: about 9% clay, low plasticity when wet, dark yellowish brown when moist. Weak indication
- Sandy layerH3best layer A very gravelly sand layer about 22 to 65 in down: about 3% clay, low plasticity when wet. Weak indication
What it looks like raw
The sandy layer (H3), 22 to 65 in down in the typical profile. Raw colour is not fired colour.
About the soil
- Parent material: coarse-loamy glaciofluvial deposits over sandy and gravelly glaciofluvial deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy over sandy or sandy-skeletal.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Vermont, in these survey areas: Washington County, Vermont.
By state: wild clay in Vermont.
USDA, distribution and extent: Central and northern New England and northern New York.
USDA, geographic setting: Nearly level or very gently sloping; slopes generally slightly concave with gradients commonly 0 to 3 percent.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Buxton: Strong lead
- Lamoine: Strong lead
- Adams: Weak indication
- Berkshire: Weak indication
- Cabot: Weak indication
- Colonel: Weak indication
- Colton: Weak indication
- Grange: Weak indication
See it on the map
Open a Machias spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Machias fine sandy loam, 0 to 3 percent slopes, map unit 33A in Washington County, Vermont.
- Official Series Description: Machias(revised 02/2006), established.
- Taxonomic class: Coarse-loamy over sandy or sandy-skeletal, isotic, frigid Aquic Haplorthods
- Rated with rule version 2026-09-28.1; the method is on the About page.