Lansdale soil
Wild-clay potential
Weak indication
Weak indication: no layer of Lansdale shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Lansdale soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Lansdale spot on the map
Rated from the USDA soil survey record for Lansdale loam, 3 to 8 percent slopes (Lancaster County, Pennsylvania) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 14% clay.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Lowers the potential Low engineering plasticity index (6.5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 26 in (66 cm)).
- Note Typically starts within about 8 in (20 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 26% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- TopsoilAp A loam layer about 0 to 8 in down: about 13% clay, low plasticity when wet, brown when moist. Weak indication
- Clay subsoilBtbest layer A channery sandy loam layer about 8 to 34 in down: about 14% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerC A channery sandy loam layer about 34 to 46 in down: about 14% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- BedrockR Bedrock about 46 to 50 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (Bt), 8 to 34 in down in the typical profile: brown (7.5YR 5/4); friable, slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from sandstone and/or residuum weathered from conglomerate.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
- Lithic bedrock typically about 46 in (117 cm) down.
Where it is mapped
Seen on the map as the most common soil in 16 map units in Pennsylvania, in these survey areas: Bucks County, Pennsylvania; Lancaster County, Pennsylvania; Montgomery County, Pennsylvania.
By state: wild clay in Pennsylvania.
USDA, distribution and extent: The north-central part of New Jersey, the southeastern part of Pennsylvania, the central part of Maryland, and Northern Virginia. The series is moderately extensive, consisting of about 15,000 acres.
USDA, geographic setting: Lansdale soils are on rolling uplands, on slopes from 0 to 25 percent. They formed in residuum weathered from arkosic sandstone and conglomerate. Average annual temperature ranges from 50 to 55 degrees F. Average annual precipitation ranges from 40 to 48 inches. Frost-free days range from 160 to 190.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Watchung: Strong lead
- Hagerstown: Strong lead
- Bowmansville: Promising
- Mount Lucas: Promising
- Readington: Promising
- Rowland: Promising
- Towhee: Promising
- Chester: Promising
See it on the map
Open a Lansdale spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 92%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Lansdale loam, 3 to 8 percent slopes, map unit LaB in Lancaster County, Pennsylvania.
- Official Series Description: Lansdale(revised 09/2008), established.
- Taxonomic class: Coarse-loamy, mixed, active, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.