Kingstowne soil
Wild-clay potential
Possible
Possible: dug, graded, or filled ground; USDA estimates a loamy layer with some clay typically about 4 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Kingstowne soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Kingstowne spot on the map
Rated from the USDA soil survey record for Kingstowne sandy clay loam, 0 to 45 percent slopes (Alexandria City, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 32% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (23): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 56 in (142 cm)).
- Note Typically starts within about 4 in (10 cm) of the surface.
- Note Few rock fragments (about 13% by volume).
Layer by layer
- TopsoilH1 A sandy clay loam layer about 0 to 4 in down: about 24% clay, moderate plasticity when wet, brown when moist. Weak indication
- Loamy layerH2best layer A clay loam layer about 4 to 60 in down: about 32% clay, high plasticity when wet, gray when moist. Promising
What it looks like raw
The loamy layer (H2), 4 to 60 in down in the typical profile: gray (10YR 6/1); firm, moderately sticky, moderately plastic. Raw colour is not fired colour.
About the soil
- Dug, graded, or filled ground, not a natural soil. USDA's layers for Kingstowne are an estimate for moved material and can change within a few steps, so it is rated no higher than Possible.
- Parent material: Earthy fill of fluviomarine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 17 map units in Virginia, in these survey areas: Alexandria City, Virginia; Fairfax County, Virginia.
By state: wild clay in Virginia.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Lunt: Strong lead
- Sumerduck: Strong lead
- Gunston: Strong lead
- Orange: Strong lead
- Fairfax: Promising
- Elkton: Promising
- Elsinboro: Promising
- Glenelg: Promising
See it on the map
Open a Kingstowne spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Kingstowne sandy clay loam, 0 to 45 percent slopes, map unit 66 in Alexandria City, Virginia.
- Official Series Description: Kingstowne(revised 10/2021), tentative.
- Taxonomic class: Fine-loamy, mixed, semiactive, acid, mesic Typic Udorthents
- Rated with rule version 2026-09-28.1; the method is on the About page.