Elsinboro soil
Wild-clay potential
Promising
Promising: a loamy layer with some clay typically about 5 to 32 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Elsinboro soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Elsinboro spot on the map
Rated from the USDA soil survey record for Elsinboro-Delanco complex, 2 to 7 percent slopes, rarely flooded (Culpeper County, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 28% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (19).
- Raises the potential The official series description calls the wet soil slightly sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 27 in (69 cm)).
- Note Typically starts within about 5 in (13 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- Sandy layerH1 A loam layer about 0 to 5 in down: about 13% clay, moderate plasticity when wet, brown when moist. Weak indication
- Loamy layerH2best layer A clay loam layer about 5 to 32 in down: about 28% clay, moderate plasticity when wet, brown when moist. Promising
- Loamy layerH3 A silty clay loam layer about 32 to 60 in down: about 28% clay, moderate plasticity when wet, reddish yellow when moist. Possible
What it looks like raw
The loamy layer (H2), 5 to 32 in down in the typical profile: brown (7.5YR 5/4); friable, slightly sticky, moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium derived from igneous, metamorphic and sedimentary rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 14 map units in Delaware, Maryland, Virginia, in these survey areas: Baltimore County, Maryland; Cecil County, Maryland; Culpeper County, Virginia; Fairfax County, Virginia; Fauquier County, Virginia; Harford County Area, Maryland; New Castle County, Delaware; Prince William County, Virginia.
By state: wild clay in Delaware,wild clay in Maryland,wild clay in Virginia.
USDA, distribution and extent: Distribution: Delaware, Maryland, Virginia, North Carolina and possibly in New Jersey and Pennsylvania
USDA, geographic setting: MLRA(s): 130, 148, 149A
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Montalto: Strong lead
- Watchung: Strong lead
- Jackland: Strong lead
- Albano: Strong lead
- Appling: Strong lead
- Cecil: Strong lead
- Christiana: Strong lead
- Kelly: Strong lead
See it on the map
Open a Elsinboro spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 50%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Elsinboro-Delanco complex, 2 to 7 percent slopes, rarely flooded, map unit 21B in Culpeper County, Virginia.
- Official Series Description: Elsinboro(revised 12/2012), established.
- Taxonomic class: Fine-loamy, mixed, semiactive, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.