Kentuck soil
Wild-clay potential
Promising
Promising: a loamy layer with some clay typically about 24 to 45 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Kentuck soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Kentuck spot on the map
Rated from the USDA soil survey record for Kentuck silt loam (Harford County, Aberdeen Proving Ground, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 29% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (17.5).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 21 in (53 cm)).
- Note Typically starts about 24 in (61 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 13 in down: about 17% clay, moderate plasticity when wet, black when moist. Weak indication
- Sandy layerH2 A silt loam layer about 13 to 24 in down: about 17% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Loamy layerH3best layer A silty clay loam layer about 24 to 45 in down: about 29% clay, moderate plasticity when wet, light brownish gray when moist. Promising
- Sandy layerH4 A fine sandy loam layer about 45 to 56 in down: about 13% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerH5 A fine sand layer about 56 to 70 in down: about 6% clay, low plasticity when wet, light gray when moist. Weak indication
What it looks like raw
The loamy layer (H3), 24 to 45 in down in the typical profile: light brownish gray (10YR 6/2); friable; moderately sticky, moderately plastic. Raw colour is not fired colour.
About the soil
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: very poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Maryland, in these survey areas: Cecil County, Maryland; Harford County, Aberdeen Proving Ground, Maryland.
By state: wild clay in Maryland.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Lenni: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Elkton: Promising
- Lenape: Promising
- Aquasco: Promising
- Baile: Promising
See it on the map
Open a Kentuck spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Kentuck silt loam, map unit Kn in Harford County, Aberdeen Proving Ground, Maryland.
- Official Series Description: Kentuck(revised 11/2015), established.
- Taxonomic class: Fine-silty, mixed, active, mesic Typic Umbraquults
- Rated with rule version 2026-09-28.1; the method is on the About page.