Indiantown soil
Wild-clay potential
Weak indication
Weak indication: no layer of Indiantown shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Indiantown soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Indiantown spot on the map
Rated from the USDA soil survey record for Indiantown mucky silt loam (Harford County, Aberdeen Proving Ground, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 6% clay.
- Lowers the potential Low engineering plasticity index (2): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 31 in (79 cm)).
- Note Typically starts about 41 in (104 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
Layer by layer
- Sandy layerH1 A mucky silt loam layer about 0 to 25 in down: about 12% clay, low plasticity when wet, very dark brown when moist. Weak indication
- Sandy layerH2 A loamy sand layer about 25 to 41 in down: about 10% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerH3best layer A sand layer about 41 to 72 in down: about 6% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 41 to 72 in down in the typical profile: dark grayish brown (2.5Y 4/2); loose. Raw colour is not fired colour.
About the soil
- USDA family mineralogy: siliceous.
- USDA family particle-size class: coarse-loamy.
- Drainage: very poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Maryland, in these survey areas: Harford County, Aberdeen Proving Ground, Maryland.
By state: wild clay in Maryland.
USDA, distribution and extent: Flood plains of the mid-Atlantic Coastal Plain of Maryland, Delaware, and New Jersey. This series is of small extent.
USDA, geographic setting: The Indiantown soils are nearly level soils located on narrow low gradient flood plains of the mid-Atlantic Coastal Plain. The slopes range from 0 to 1 percent. These soils formed in loamy fluvial sediments overlying sandy alluvial and marine sediments. Mean annual temperature ranges from 52 to 58 degrees F., and mean annual precipitation ranges from 38 to 48 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Elkton: Promising
- Kentuck: Promising
- Lenape: Promising
- Beltsville: Possible
- Codorus: Possible
- Corsica: Possible
- Fallsington: Possible
- Hambrook: Possible
See it on the map
Open a Indiantown spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Indiantown mucky silt loam, map unit In in Harford County, Aberdeen Proving Ground, Maryland.
- Official Series Description: Indiantown(revised 11/2015), established.
- Taxonomic class: Coarse-loamy, siliceous, active, acid, mesic Cumulic Humaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.