Corsica soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 18 to 40 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Corsica soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Corsica spot on the map
Rated from the USDA soil survey record for Corsica loam (Harford County, Aberdeen Proving Ground, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 24% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (10).
- Raises the potential The official series description calls the wet soil slightly sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 22 in (56 cm)).
- Note Typically starts within about 18 in (46 cm) of the surface.
- Note Few rock fragments (about 4% by volume).
Layer by layer
- Sandy layerH1 A loam layer about 0 to 12 in down: about 11% clay, low plasticity when wet, black when moist. Weak indication
- Sandy layerH2 A loam layer about 12 to 18 in down: about 13% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Loamy layerH3best layer A sandy clay loam layer about 18 to 40 in down: about 24% clay, moderate plasticity when wet, light gray when moist. Possible
- Sandy layerH4 A sandy loam layer about 40 to 48 in down: about 15% clay, low plasticity when wet, gray when moist. Weak indication
- Sandy layerH5 A stratified gravelly sand to clay loam layer about 48 to 72 in down: about 18% clay, moderate plasticity when wet, stratified light gray when moist. Weak indication
What it looks like raw
The loamy layer (H3), 18 to 40 in down in the typical profile: light gray (2.5Y 7/2); friable, slightly sticky, plastic. Raw colour is not fired colour.
About the soil
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: very poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Maryland, in these survey areas: Harford County, Aberdeen Proving Ground, Maryland.
By state: wild clay in Maryland.
USDA, distribution and extent: .
USDA, geographic setting: Landscape: Coastal Plain Upland
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Elkton: Promising
- Kentuck: Promising
- Lenape: Promising
- Beltsville: Possible
- Codorus: Possible
- Fallsington: Possible
- Hambrook: Possible
- Mattapex: Possible
See it on the map
Open a Corsica spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Corsica loam, map unit Co in Harford County, Aberdeen Proving Ground, Maryland.
- Official Series Description: Corsica(revised 11/2015), established.
- Taxonomic class: Fine-loamy, mixed, active, mesic Typic Umbraquults
- Rated with rule version 2026-09-28.1; the method is on the About page.