Mattapex soil
Wild-clay potential
Possible
Possible: a clay-enriched layer typically about 15 to 36 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Mattapex soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Mattapex spot on the map
Rated from the USDA soil survey record for Mattapex-Butlertown complex, 5 to 10 percent slopes (Kent County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 23% clay. It may need settling or refining to become a clay body.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (10).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 21 in (53 cm)).
- Note Typically starts within about 15 in (38 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilAp A silt loam layer about 0 to 11 in down: about 13% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerBE A silt loam layer about 11 to 15 in down: about 13% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Clay subsoilBtbest layer A silt loam layer about 15 to 36 in down: about 23% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Sandy layer2C1 A fine sandy loam layer about 36 to 60 in down: about 9% clay, low plasticity when wet, light gray when moist. Weak indication
- Sandy layer2C2 A loamy sand layer about 60 to 80 in down: about 6% clay, low plasticity when wet, light brownish gray when moist. Weak indication
What it looks like raw
The clay subsoil (Bt), 15 to 36 in down in the typical profile: yellowish brown (10YR 5/6); friable, slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: silty eolian deposits over fluviomarine sediments.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 27 map units in Delaware, Maryland, New Jersey, Pennsylvania, Virginia, in these survey areas: Baltimore County, Maryland; Cecil County, Maryland; Chester County, Pennsylvania; Fairfax County, Virginia; Harford County Area, Maryland; Harford County, Aberdeen Proving Ground, Maryland; Kent County, Maryland; New Castle County, Delaware; Salem County, New Jersey.
By state: wild clay in Delaware,wild clay in Maryland,wild clay in New Jersey,wild clay in Pennsylvania,wild clay in Virginia.
USDA, distribution and extent: Distribution: Coastal Plain of Maryland, Delaware, New Jersey, Pennsylvania and Virginia
USDA, geographic setting: Landscape: Coastal Plain, upland, lowland
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Watchung: Strong lead
- Montalto: Strong lead
- Christiana: Strong lead
- Benevola: Strong lead
- Cumberstone: Strong lead
- Gunston: Strong lead
- Jackland: Strong lead
- Kelly: Strong lead
See it on the map
Open a Mattapex spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 40%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Mattapex-Butlertown complex, 5 to 10 percent slopes, map unit MqC in Kent County, Maryland.
- Official Series Description: Mattapex(revised 10/2008), established.
- Taxonomic class: Fine-silty, mixed, active, mesic Aquic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.