Holcomb soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 24 to 50 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Holcomb soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Holcomb spot on the map
Rated from the USDA soil survey record for Holcomb silt loam (Marion County Area, Oregon) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 45% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (45): USDA's estimate suggests plastic behavior when wet.
- Note Thick enough to investigate (about 26 in (66 cm)).
- Note Typically starts about 24 in (61 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 13% by volume).
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 18 in down: about 23% clay, moderate plasticity when wet, light brownish gray when moist. Possible
- Loamy layerH2 A silty clay loam layer about 18 to 24 in down: about 28% clay, moderate plasticity when wet, light brownish gray when moist. Promising
- Clay-rich layerH3best layer A silty clay layer about 24 to 50 in down: about 45% clay, high plasticity when wet, grayish brown when moist. Strong lead
- Loamy layerH4 A silt loam layer about 50 to 60 in down: about 27% clay, moderate plasticity when wet, grayish brown when moist. Possible
What it looks like raw
The clay-rich layer (H3), 24 to 50 in down in the typical profile: grayish brown (10YR 5/2) dry, dark grayish brown (10YR 4/2) moist. Raw colour is not fired colour.
About the soil
- Parent material: silty and clayey alluvium with some loess in the upper layers.
- USDA family particle-size class: fine.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Oregon, in these survey areas: Marion County Area, Oregon.
By state: wild clay in Oregon.
USDA, distribution and extent: Willamette Valley, Oregon; MLRA 2; moderate extent
USDA, geographic setting: Elevation--40 to 200 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bashaw: Strong lead
- Concord: Strong lead
- Dayton: Strong lead
- Labish: Strong lead
- McBee: Strong lead
- Amity: Promising
- Chehalis: Promising
- Wapato: Promising
See it on the map
Open a Holcomb spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Holcomb silt loam, map unit Ho in Marion County Area, Oregon.
- Official Series Description: Holcomb(revised 12/2017), established.
- Taxonomic class: Fine, smectitic, mesic Xeric Argialbolls
- Rated with rule version 2026-09-28.1; the method is on the About page.