Bashaw soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 14 to 48 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bashaw soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Bashaw clay (Marion County Area, Oregon) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 63% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (50): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 34 in (86 cm)).
- Note Typically starts within about 14 in (36 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Clay-rich layerH1 A clay layer about 0 to 14 in down: about 63% clay, high plasticity when wet, very dark gray when moist. Strong lead
- Clay-rich layerH2best layer A clay layer about 14 to 48 in down: about 63% clay, high plasticity when wet, very dark gray when moist. Strong lead
- Clay-rich layerH3 A clay layer about 48 to 60 in down: about 60% clay, high plasticity when wet, light brownish gray when moist. Promising
What it looks like raw
The clay-rich layer (H2), 14 to 48 in down in the typical profile: very dark gray (N 3/0) dry, black (N 2/0) moist; very hard, very firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: very-fine.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Oregon, in these survey areas: Marion County Area, Oregon.
By state: wild clay in Oregon.
USDA, distribution and extent: Willamette Valley, MLRA 2; Umpqua Valley, MLRA 5; moderate extent
USDA, geographic setting: Elevation--30 to 250 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Concord: Strong lead
- Dayton: Strong lead
- Holcomb: Strong lead
- Labish: Strong lead
- McBee: Strong lead
- Amity: Promising
- Chehalis: Promising
- Wapato: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bashaw clay, map unit Ba in Marion County Area, Oregon.
- Official Series Description: Bashaw(revised 12/2017), established.
- Taxonomic class: Very-fine, smectitic, mesic Xeric Endoaquerts
- Rated with rule version 2026-09-28.1; the method is on the About page.