Dayton soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 13 to 46 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Dayton soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Dayton silt loam (Marion County Area, Oregon) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 45% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (40): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 33 in (84 cm)).
- Note Typically starts within about 13 in (33 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 13 in down: about 18% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- Clay-rich layerH2best layer A clay layer about 13 to 46 in down: about 45% clay, high plasticity when wet, gray when moist. Strong lead
- Loamy layerH3 A silty clay loam layer about 46 to 60 in down: about 28% clay, moderate plasticity when wet, dark gray when moist. Promising
What it looks like raw
The clay-rich layer (H2), 13 to 46 in down in the typical profile: gray (5Y 5/1), light gray (5Y 7/2) dry; hard, firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: mixed alluvium with some loess in the upper layers.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Oregon, in these survey areas: Marion County Area, Oregon.
By state: wild clay in Oregon.
USDA, distribution and extent: Dayton soils are found throughout the Willamette Valley in western Oregon; MLRA 2. They are extensive.
USDA, geographic setting: The Dayton soils are on nearly level or somewhat concave, slightly depressed parts of broad valley terraces at elevations of 150 to 400 feet. They formed in silty and clayey glaciolacustrine deposits. Summers are warm and dry and winters are cool and moist. Average January temperature is 39 to 40 degrees F., average July temperature is 65 to 67 degrees F., and mean annual temperature is 50 to 54 degrees F. Mean annual precipitation is 40 to 50 inches. The frost-free period is 165 to 210 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bashaw: Strong lead
- Concord: Strong lead
- Holcomb: Strong lead
- Labish: Strong lead
- McBee: Strong lead
- Amity: Promising
- Chehalis: Promising
- Wapato: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 95%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Dayton silt loam, map unit Da in Marion County Area, Oregon.
- Official Series Description: Dayton(revised 02/2015), established.
- Taxonomic class: Fine, smectitic, mesic Vertic Albaqualfs
- Rated with rule version 2026-09-28.1; the method is on the About page.