Gilpin soil
Wild-clay potential
Possible
Possible: a surface layer with some clay typically about 1 to 7 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Gilpin soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Gilpin silt loam, 35 to 65 percent slopes, stony (Cabell County, West Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 21% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (9.5).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Moderate thickness (about 6 in (15 cm)).
- Note Typically starts within about 1 in (3 cm) of the surface.
- Note Few rock fragments (about 12% by volume).
- Note Surface layer; expect roots and organic matter.
Layer by layer
- Organic top layerOa An organic top layer about 0 to 1 in down, not a clay body. Weak indication
- TopsoilAbest layer A silt loam layer about 1 to 7 in down: about 21% clay, moderate plasticity when wet, dark grayish brown when moist. Possible
- Loamy layerBA+Bt1-2+BC A very channery loam layer about 7 to 35 in down: about 27% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Loamy layerC A very channery loam layer about 35 to 36 in down: about 25% clay, moderate plasticity when wet, brown when moist. Weak indication
- BedrockR Unweathered bedrock about 36 to 40 in down: no clay layer to dig. Weak indication
What it looks like raw
The topsoil (A), 1 to 7 in down in the typical profile: dark grayish brown (10YR 4/2); friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: fine-loamy residuum weathered from shale and siltstone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
- Lithic bedrock typically about 36 in (91 cm) down.
Where it is mapped
Seen on the map as the most common soil in 16 map units in Pennsylvania, West Virginia, in these survey areas: Cabell County, West Virginia; Venango County, Pennsylvania; Warren and Forest Counties, Pennsylvania.
By state: wild clay in Pennsylvania,wild clay in West Virginia.
USDA, distribution and extent: Distribution: Pennsylvania, Georgia, Indiana, Kentucky, Maryland, New York, Ohio, Tennessee, Virginia, and West Virginia
USDA, geographic setting: MLRA(s) using this series: 118, 119, 120, 122, 123, 124, 125, 126, 127, 128, 130, 147
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cavode: Strong lead
- Armagh: Strong lead
- Vandalia: Strong lead
- Ernest: Promising
- Wharton: Promising
- Brinkerton: Promising
- Guyan: Promising
- Shelmadine: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Gilpin silt loam, 35 to 65 percent slopes, stony, map unit GpF in Cabell County, West Virginia.
- Official Series Description: Gilpin(revised 10/2014), established.
- Taxonomic class: Fine-loamy, mixed, active, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.