Fort Mott soil
Wild-clay potential
Weak indication
Weak indication: no layer of Fort Mott shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Fort Mott soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Fort Mott spot on the map
Rated from the USDA soil survey record for Fort Mott loamy sand, 0 to 5 percent slopes (Baltimore County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 6% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 37 in (94 cm)).
- Note Typically starts about 33 in (84 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilAp A loamy sand layer about 0 to 12 in down: about 4% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerBE A loamy sand layer about 12 to 21 in down: about 7% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Clay subsoilBt A sandy loam layer about 21 to 33 in down: about 12% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerBCbest layer A sand layer about 33 to 70 in down: about 6% clay, low plasticity when wet, strong brown when moist. Weak indication
- Sandy layerC A loamy sand layer about 70 to 80 in down: about 6% clay, low plasticity when wet, strong brown when moist. Weak indication
What it looks like raw
The sandy layer (BC), 33 to 70 in down in the typical profile: strong brown (7.5YR 5/6); loose. Raw colour is not fired colour.
About the soil
- Parent material: sandy eolian deposits over loamy fluviomarine deposits.
- USDA family mineralogy: siliceous.
- USDA family particle-size class: loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Maryland, in these survey areas: Baltimore County, Maryland.
By state: wild clay in Maryland.
USDA, geographic setting: Landscape: Coastal Plain upland
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Benevola: Strong lead
- Christiana: Strong lead
- Cumberstone: Strong lead
- Jackland: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Baile: Promising
- Baltimore: Promising
See it on the map
Open a Fort Mott spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Fort Mott loamy sand, 0 to 5 percent slopes, map unit FcB in Baltimore County, Maryland.
- Official Series Description: Fort Mott(revised 11/2015), established.
- Taxonomic class: Loamy, siliceous, semiactive, mesic Arenic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.