Bryan soil
Wild-clay potential
Weak indication
Weak indication: no layer of Bryan shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bryan soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Bryan coarse sandy loam, 40 to 60 percent slopes (Adams-Washington Area, Parts of Adams and Washington Counties, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 5% clay.
- Lowers the potential Low engineering plasticity index (5): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 46 in (116 cm)).
- Note Typically starts within about 17 in (44 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 22% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Organic top layerOi An organic top layer about 0 to 1 in down, not a clay body. Weak indication
- Organic top layerOe An organic top layer about 1 to 3 in down, not a clay body. Weak indication
- TopsoilA A coarse sandy loam layer about 3 to 17 in down: about 9% clay, moderate plasticity when wet, brown when moist. Weak indication
- Sandy layerCbest layer A gravelly loamy coarse sand layer about 17 to 63 in down: about 5% clay, low plasticity when wet, very pale brown when moist. Weak indication
What it looks like raw
The sandy layer (C), 17 to 63 in down in the typical profile: very pale brown (10YR 7/3), brown (10YR 5/3) moist; slightly hard, very friable. Raw colour is not fired colour.
About the soil
- Parent material: volcanic ash and/or colluvium derived from quartz-diorite and/or granodiorite and/or quartz-monzonite.
- USDA family mineralogy: mixed.
- USDA family particle-size class: sandy.
- Drainage: excessively drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Idaho, in these survey areas: Adams-Washington Area, Parts of Adams and Washington Counties, Idaho; South Idaho Forests, Idaho; Valley Area, Idaho, Parts of Adams and Valley Counties.
By state: wild clay in Idaho.
USDA, distribution and extent: This series is moderately extensive in the border zones of the Idaho Batholith. It is about 45,000 acres in extent. MLRA 43B.
USDA, geographic setting: Landform - mountain slopes
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cabarton: Strong lead
- Sudpeak: Strong lead
- Blackwell: Promising
- Swede: Promising
- Catherine: Promising
- Culdecole: Promising
- Nisula: Promising
- Ticanot: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bryan coarse sandy loam, 40 to 60 percent slopes, map unit 28 in Adams-Washington Area, Parts of Adams and Washington Counties, Idaho.
- Official Series Description: Bryan(revised 02/2016), established.
- Taxonomic class: Sandy, mixed Lamellic Humicryepts
- Rated with rule version 2026-09-28.1; the method is on the About page.