Barbour soil
Wild-clay potential
Weak indication
Weak indication: no layer of Barbour shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Barbour soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Barbour spot on the map
Rated from the USDA soil survey record for Barbour loam (Delaware County, New York) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 5% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 46 in (117 cm)).
- Note Typically starts about 26 in (66 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 50% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- TopsoilAp A loam layer about 0 to 6 in down: about 12% clay, low plasticity when wet, dark reddish brown when moist. Weak indication
- Sandy layerBw1 A silt loam layer about 6 to 18 in down: about 12% clay, low plasticity when wet, reddish brown when moist. Weak indication
- Sandy layerBw2 A gravelly loam layer about 18 to 26 in down: about 12% clay, low plasticity when wet, reddish brown when moist. Weak indication
- Sandy layer2Cbest layer A very gravelly loamy sand layer about 26 to 72 in down: about 5% clay, low plasticity when wet, reddish brown when moist. Weak indication
What it looks like raw
The sandy layer (2C), 26 to 72 in down in the typical profile: reddish brown (5YR 4/4); very gravelly loamy sand; loose. Raw colour is not fired colour.
About the soil
- Parent material: loamy over sandy and gravelly alluvium derived mainly from areas of acid, reddish sandstone, siltstone, and shale.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy over sandy or sandy-skeletal.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 4 map units in New York, in these survey areas: Delaware County, New York; Schoharie County, New York.
By state: wild clay in New York.
USDA, distribution and extent: Southern and eastern New York, Pennsylvania, Maryland, New Jersey, and West Virginia. MLRA's 140, 127, 147, and 148. The series is moderately extensive.
USDA, geographic setting: Barbour soils are on convex or plane flood plains, alluvial fans, and low terraces. They formed in alluvium from areas of reddish sandstone, siltstone, and shale in both glaciated and residual areas. Slope ranges from 0 to 8 percent. Mean annual temperature ranges from 45 to 50 degrees F.; mean annual precipitation ranges from 32 to 45 inches; mean frost-free season ranges from 120 to 180 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Lakemont: Strong lead
- Phelps: Strong lead
- Holly: Promising
- Basher: Weak indication
- Bath: Weak indication
- Lackawanna: Weak indication
- Lordstown: Weak indication
- Mardin: Weak indication
See it on the map
Open a Barbour spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Barbour loam, map unit Bc in Delaware County, New York.
- Official Series Description: Barbour(revised 04/2001), established.
- Taxonomic class: Coarse-loamy over sandy or sandy-skeletal, mixed, active, mesic Fluventic Dystrudepts
- Rated with rule version 2026-09-28.1; the method is on the About page.