Assinniboine soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 7 to 16 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Assinniboine soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Assinniboine spot on the map
Rated from the USDA soil survey record for Assinniboine fine sandy loam, 2 to 6 percent slopes (Meade County, South Dakota, Northern Part) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 24% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (15).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Moderate thickness (about 9 in (23 cm)).
- Note Typically starts within about 7 in (18 cm) of the surface.
- Missing data Rock fragment content is not reported.
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 7 in down: about 10% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Loamy layerH2best layer A sandy clay loam layer about 7 to 16 in down: about 24% clay, moderate plasticity when wet, brown when moist. Possible
- Sandy layerH3 A fine sandy loam layer about 16 to 60 in down: about 17% clay, moderate plasticity when wet, light gray when moist. Weak indication
What it looks like raw
The loamy layer (H2), 7 to 16 in down in the typical profile: brown (10YR 5/3), brown (10YR 4/3) moist; hard, very friable, sticky and plastic. Raw colour is not fired colour.
About the soil
- Parent material: eolian deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in South Dakota, in these survey areas: Meade County, South Dakota, Northern Part.
By state: wild clay in South Dakota.
USDA, distribution and extent: Assinniboine soils are of moderate extent in Montana, South Dakota, Wyoming, and Colorado. MLRAs 43B, 44B, 46, 52, 58A, and 58D.
USDA, geographic setting: Landform - till plains, alluvial fans, fan remnants, hills, drainageways, sedimentary plains, and stream terraces.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Abor: Strong lead
- Absher: Strong lead
- Gerdrum: Strong lead
- Grail: Strong lead
- Heil: Strong lead
- Hisle: Strong lead
- Kyle: Strong lead
- Lawther: Strong lead
See it on the map
Open a Assinniboine spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Assinniboine fine sandy loam, 2 to 6 percent slopes, map unit AsB in Meade County, South Dakota, Northern Part.
- Official Series Description: Assinniboine(revised 04/2016), established.
- Taxonomic class: Fine-loamy, mixed, superactive, frigid Aridic Argiustolls
- Rated with rule version 2026-09-28.1; the method is on the About page.