Annemessex soil
Wild-clay potential
Possible
Possible: a clay-enriched layer typically about 8 to 18 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Annemessex soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Annemessex spot on the map
Rated from the USDA soil survey record for Annemessex loam, 0 to 2 percent slopes (Cecil County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 25% clay. It may need settling or refining to become a clay body.
- Note USDA labels this a "Bt1" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (11).
- Raises the potential The official series description calls the wet soil slightly sticky and moderately plastic (a field observation, not a ceramic test).
- Note Moderate thickness (about 10 in (25 cm)).
- Note Typically starts within about 8 in (20 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilAp A loam layer about 0 to 2 in down: about 12% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerE A silt loam layer about 2 to 8 in down: about 14% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Clay subsoilBt1best layer A silt loam layer about 8 to 18 in down: about 25% clay, moderate plasticity when wet, light yellowish brown when moist. Possible
- Clay subsoilBt2 A loam layer about 18 to 44 in down: about 17% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- Sandy layerBC A loamy fine sand layer about 44 to 57 in down: about 10% clay, low plasticity when wet, pale brown when moist. Weak indication
- Sandy layer2BCg A loamy very fine sand layer about 57 to 80 in down: about 10% clay, low plasticity when wet, light brownish gray when moist. Weak indication
What it looks like raw
The clay subsoil (Bt1), 8 to 18 in down in the typical profile: light yellowish brown (2.5Y 6/4), and dark grayish brown (10YR 4/2); loam; friable, slightly sticky and moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: loamy fluviomarine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Maryland, in these survey areas: Cecil County, Maryland.
By state: wild clay in Maryland.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Lenni: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Aquasco: Promising
- Baile: Promising
- Chillum: Promising
- Chrome: Promising
See it on the map
Open a Annemessex spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Annemessex loam, 0 to 2 percent slopes, map unit AnA in Cecil County, Maryland.
- Official Series Description: Annemessex(revised 11/2015), established.
- Taxonomic class: Fine-loamy, mixed, semiactive, mesic Aquic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.