Sisk soil
Wild-clay potential
Weak indication
Weak indication: no layer of Sisk shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Sisk soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Sisk-Glebe association, steep, very stony (Coos County Area, New Hampshire) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 9% clay.
- Lowers the potential Low engineering plasticity index (4): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 45 in (114 cm)).
- Note Typically starts within about 20 in (51 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 29% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Organic top layerOa An organic top layer about 0 to 2 in down, not a clay body. Weak indication
- Sandy layerH1 A silt loam layer about 2 to 6 in down: about 7% clay, low plasticity when wet, dusky red when moist. Weak indication
- Sandy layerH2 A gravelly silt loam layer about 6 to 20 in down: about 9% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerH3best layer A gravelly silt loam layer about 20 to 65 in down: about 9% clay, low plasticity when wet, brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 20 to 65 in down in the typical profile: brown (10YR 5/3); firm. Raw colour is not fired colour.
About the soil
- Parent material: till.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in New Hampshire, Vermont, in these survey areas: Coos County Area, New Hampshire; Washington County, Vermont.
By state: wild clay in New Hampshire,wild clay in Vermont.
USDA, distribution and extent: Mountains of Maine, Vermont, New Hampshire, and New York. MLRA 143. The series is of moderate extent.
USDA, geographic setting: Sisk soils are in high elevation valleys and on side slopes of mountain ridges at elevations greater than 700 meters. Slope ranges from 12 to 60 percent. The soils formed in dense till. The mean annual temperature ranges from 0 to 6 degrees C and the mean annual precipitation ranges from 102 to 152 centimeters. The frost-free season ranges from 30 to 90 days. Elevations range from 700 to 1600 meters above mean sea level.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Buxton: Strong lead
- Lamoine: Strong lead
- Adams: Weak indication
- Berkshire: Weak indication
- Colton: Weak indication
- Grange: Weak indication
- Hogback: Weak indication
- Nicholville: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 60%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Sisk-Glebe association, steep, very stony, map unit 736E in Coos County Area, New Hampshire.
- Official Series Description: Sisk(revised 03/2011), established.
- Taxonomic class: Coarse-loamy, isotic Oxyaquic Humicryods
- Rated with rule version 2026-09-28.1; the method is on the About page.