Sinclair soil
Wild-clay potential
Weak indication
Weak indication: no layer of Sinclair shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Sinclair soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Sinclair spot on the map
Rated from the USDA soil survey record for Sinclair gravelly sandy loam, 0 to 15 percent slopes (Jefferson County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 35 in (88 cm)).
- Note Typically starts about 25 in (64 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential Noticeable rock fragments (about 34% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Sandy layerH1 A gravelly sandy loam layer about 0 to 8 in down: about 10% clay, low plasticity when wet, dark brown when moist. Weak indication
- Sandy layerH2 A gravelly sandy loam layer about 8 to 25 in down: about 10% clay, low plasticity when wet, dark brown when moist. Weak indication
- Sandy layerH3best layer A gravelly sandy loam layer about 25 to 60 in down: about 10% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 25 to 60 in down in the typical profile: dark grayish brown (10YR 4/2), light brownish gray (2.5Y 6/2) dry; very hard, very firm. Raw colour is not fired colour.
About the soil
- Parent material: basal till.
- USDA family particle-size class: ashy-skeletal.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Washington, in these survey areas: Jefferson County Area, Washington; Kitsap County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Northwestern Washington. Series is of moderate extent.
USDA, geographic setting: Sinclair soils are on slightly undulating to steep uplands at elevations from 100 to 800 feet. They formed in glacial till. The climate is marine with cool, dry summers and mild, wet winters. The annual precipitation ranges from 25 to 50 inches and falls mostly as rain from November through March. The mean January temperature is about 39 degrees F.; the mean July temperature is 59 degrees F.; and the mean annual temperature is about 50 degrees F. The average frost free season is about 200 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bellingham: Strong lead
- Quilcene: Strong lead
- McKenna: Promising
- Shalcar: Promising
- Wapato: Promising
- Kitsap: Possible
- Lummi: Possible
- Alderwood: Weak indication
See it on the map
Open a Sinclair spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Sinclair gravelly sandy loam, 0 to 15 percent slopes, map unit SnC in Jefferson County Area, Washington.
- Official Series Description: Sinclair(revised 09/2004), established.
- Taxonomic class: Loamy-skeletal, isotic, mesic Andic Durorthods
- Rated with rule version 2026-09-28.1; the method is on the About page.