Saltair soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 30 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Saltair soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Saltair spot on the map
Rated from the USDA soil survey record for Saltair silty clay loam, 0 to 1 percent slopes (Box Elder County, Utah, Eastern Part) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 39% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (22.5): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 30 in (76 cm)).
- Note Typically starts about 30 in (76 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note USDA reports about 28% calcium carbonate; lime in a clay body deserves testing.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Loamy layerH1 A silty clay loam layer about 0 to 7 in down: about 32% clay, moderate plasticity when wet, light gray when moist. Promising
- Loamy layerH2 A silty clay loam layer about 7 to 20 in down: about 32% clay, moderate plasticity when wet, pale yellow when moist. Promising
- Loamy layerH3 A silt loam layer about 20 to 30 in down: about 24% clay, moderate plasticity when wet, light gray when moist. Possible
- Clay-rich layerH4best layer A silty clay loam layer about 30 to 60 in down: about 39% clay, high plasticity when wet, light gray when moist. Strong lead
What it looks like raw
The clay-rich layer (H4), 30 to 60 in down in the typical profile: light gray (2.5Y 7/2), light brownish gray (2.5Y 6/2) moist; hard, firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: lacustrine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 6 map units in Utah, in these survey areas: Box Elder County, Utah, Eastern Part; Davis-Weber Area, Utah; Salt Lake Area, Utah.
By state: wild clay in Utah.
USDA, distribution and extent: Northern Utah and northeastern Nevada. These soils are extensive with about 450,000 acres of the series mapped to date. The series concept and main acreage is in MLRA 28A, while other acreage occurs in MLRA 34B.
USDA, geographic setting: Saltair soils are on lake plains and basin floors. They formed in lacustrine deposits and some alluvium derived mainly from limestone, shale, and quartzite. Slopes are 0 to 2 percent. Elevations range from 4,200 to 4,900 feet. The climate is dry subhumid and semiarid. The mean annual precipitation is 12 to 16 inches, but ranges as long as 6 inches in some survey areas. The mean annual temperature is 45 to 54 degrees F., the mean summer temperature is 68 to 73 degrees F., and the frost-free period is 110 to 180 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Eimarsh: Strong lead
- Pintailake: Strong lead
- Lasil: Strong lead
- Payson: Strong lead
- Woods Cross: Strong lead
- Abbott: Strong lead
- Airport: Strong lead
- Bramwell: Strong lead
See it on the map
Open a Saltair spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Saltair silty clay loam, 0 to 1 percent slopes, map unit SA in Box Elder County, Utah, Eastern Part.
- Official Series Description: Saltair(revised 11/2007), established.
- Taxonomic class: Fine-silty, mixed, superactive, mesic Typic Aquisalids
- Rated with rule version 2026-09-28.1; the method is on the About page.