Pyle soil
Wild-clay potential
Weak indication
Weak indication: no layer of Pyle shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Pyle soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Pyle-Koppes complex, 20 to 40 percent slopes (Valley Area, Idaho, Parts of Adams and Valley Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 19 in (48 cm)).
- Note Typically starts within about 15 in (39 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 17% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Organic top layerOi An organic top layer about 0 to 1 in down, not a clay body. Weak indication
- TopsoilAC A loamy coarse sand layer about 1 to 15 in down: about 8% clay, low plasticity when wet, pale brown when moist. Weak indication
- Sandy layerCbest layer A gravelly sand layer about 15 to 34 in down: about 3% clay, low plasticity when wet, very pale brown when moist. Weak indication
- BedrockCr Bedrock about 34 to 44 in down: no clay layer to dig. Weak indication
What it looks like raw
The sandy layer (C), 15 to 34 in down in the typical profile: very pale brown (10YR 7/3), and pale brown (10YR 6/3), brown (10YR 5/3); slightly hard, very friable. Raw colour is not fired colour.
About the soil
- Parent material: colluvium over residuum weathered from quartz-monzonite and/or granodiorite.
- USDA family mineralogy: mixed.
- USDA family particle-size class: not used.
- Drainage: somewhat excessively drained.
- Paralithic bedrock typically about 34 in (87 cm) down.
Where it is mapped
Seen on the map as the most common soil in 4 map units in Idaho, in these survey areas: South Idaho Forests, Idaho; Valley Area, Idaho, Parts of Adams and Valley Counties.
By state: wild clay in Idaho.
USDA, distribution and extent: Western part of the Idaho batholith; moderate extent. MLRA 43B.
USDA, geographic setting: Landform - mountain slopes, ridges
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cabarton: Strong lead
- Blackwell: Promising
- Swede: Promising
- Catherine: Promising
- Nisula: Promising
- Archabal: Possible
- Brownlee: Possible
- Tica: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 45%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Pyle-Koppes complex, 20 to 40 percent slopes, map unit 41 in Valley Area, Idaho, Parts of Adams and Valley Counties.
- Official Series Description: Pyle(revised 03/2016), established.
- Taxonomic class: Mixed Lamellic Cryopsamments
- Rated with rule version 2026-09-28.1; the method is on the About page.