Olete soil
Wild-clay potential
Weak indication
Weak indication: no layer of Olete shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Olete soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Olete very gravelly silt loam, 0 to 30 percent slopes (Jefferson County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 15% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil slightly sticky and nonplastic.
- Note Thick enough to investigate (about 15 in (38 cm)).
- Note Typically starts within about 3 in (8 cm) of the surface.
- Lowers the potential High rock content (about 43% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 A very gravelly silt loam layer about 0 to 3 in down: about 15% clay, low plasticity when wet, dark reddish brown when moist. Weak indication
- Sandy layerH2best layer A very gravelly silt loam layer about 3 to 18 in down: about 15% clay, low plasticity when wet, dusky red when moist. Weak indication
- Sandy layerH3 A very stony silt loam layer about 18 to 24 in down: about 15% clay, low plasticity when wet, weak red when moist. Weak indication
- BedrockH4 Weathered bedrock about 24 to 28 in down: no clay layer to dig. Weak indication
What it looks like raw
The sandy layer (H2), 3 to 18 in down in the typical profile: dusky red (2.5YR 3/2), pale red (2.5YR 6/2) dry; hard, friable, slightly sticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: colluvium and residuum from basalt.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
- Paralithic bedrock typically about 24 in (61 cm) down.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Washington, in these survey areas: Jefferson County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Northwestern Washington. Series is of moderate extent.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Quilcene: Strong lead
- Wapato: Promising
- Kitsap: Possible
- Lummi: Possible
- Ahl: Weak indication
- Alderwood: Weak indication
- Beausite: Weak indication
- Belfast: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Olete very gravelly silt loam, 0 to 30 percent slopes, map unit OeD in Jefferson County Area, Washington.
- Official Series Description: Olete(revised 06/1999), established.
- Taxonomic class: Loamy-skeletal, isotic, mesic Vitrandic Haploxerepts
- Rated with rule version 2026-09-28.1; the method is on the About page.