Naz soil
Wild-clay potential
Weak indication
Weak indication: no layer of Naz shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Naz soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Naz sandy loam, 20 to 55 percent slopes (Valley Area, Idaho, Parts of Adams and Valley Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 9% clay.
- Lowers the potential Low engineering plasticity index (5): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 29 in (74 cm)).
- Note Typically starts within about 2 in (5 cm) of the surface.
- Note Few rock fragments (about 10% by volume).
- Lowers the potential Surface layer with about 3% organic matter; roots and organics complicate use.
Layer by layer
- Organic top layerOe An organic top layer about 0 to 2 in down, not a clay body. Weak indication
- TopsoilAbest layer A sandy loam layer about 2 to 31 in down: about 9% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerC A coarse sandy loam layer about 31 to 49 in down: about 9% clay, low plasticity when wet, brown when moist. Weak indication
- BedrockCr Bedrock about 49 to 59 in down: no clay layer to dig. Weak indication
What it looks like raw
The topsoil (A), 2 to 31 in down in the typical profile: dark grayish brown (10YR 4/2), very dark brown (10YR 2/2) moist; soft, very friable, nonsticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: colluvium derived from granite and/or quartz-diorite and/or granodiorite over residuum weathered from granite and/or quartz-diorite and/or granodiorite.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
- Paralithic bedrock typically about 49 in (124 cm) down.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Idaho, in these survey areas: South Idaho Forests, Idaho; Valley Area, Idaho, Parts of Adams and Valley Counties.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern part of Idaho batholith. The soils are moderately extensive. MLRAs 43B, 43C, and 9.
USDA, geographic setting: Landform - sideslopes, swales, and concave positions on mountains, at lower elevations most have northerly aspects
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cabarton: Strong lead
- Blackwell: Promising
- Swede: Promising
- Catherine: Promising
- Nisula: Promising
- Archabal: Possible
- Brownlee: Possible
- Tica: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Naz sandy loam, 20 to 55 percent slopes, map unit 35 in Valley Area, Idaho, Parts of Adams and Valley Counties.
- Official Series Description: Naz(revised 08/2014), established.
- Taxonomic class: Coarse-loamy, mixed, superactive Pachic Haplocryolls
- Rated with rule version 2026-09-28.1; the method is on the About page.