Nassawango soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 16 to 36 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Nassawango soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Nassawango spot on the map
Rated from the USDA soil survey record for Nassawango silt loam, 0 to 2 percent slopes (Harford County, Aberdeen Proving Ground, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 24% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (16).
- Note The official series description calls the wet soil moderately sticky and slightly plastic.
- Note Thick enough to investigate (about 20 in (50 cm)).
- Note Typically starts within about 16 in (41 cm) of the surface.
- Missing data Rock fragment content is not reported.
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 10 in down: about 10% clay, low plasticity when wet, dark brown when moist. Weak indication
- Sandy layerH2 A silt loam layer about 10 to 16 in down: about 10% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- Loamy layerH3best layer A silt loam layer about 16 to 36 in down: about 24% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Sandy layerH4 A silt loam layer about 36 to 44 in down: about 15% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerH5 A loamy sand layer about 44 to 60 in down: about 6% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- Sandy layerH6 A fine sandy loam layer about 60 to 72 in down: about 14% clay, low plasticity when wet, light gray when moist. Weak indication
What it looks like raw
The loamy layer (H3), 16 to 36 in down in the typical profile: yellowish brown (10YR 5/6); firm; moderately sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 8 map units in Delaware, Maryland, in these survey areas: Cecil County, Maryland; Harford County, Aberdeen Proving Ground, Maryland; New Castle County, Delaware.
By state: wild clay in Delaware,wild clay in Maryland.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Montalto: Strong lead
- Watchung: Strong lead
- Christiana: Strong lead
- Lenni: Strong lead
- Talleyville: Strong lead
- Lenape: Promising
- Baile: Promising
- Delanco: Promising
See it on the map
Open a Nassawango spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Nassawango silt loam, 0 to 2 percent slopes, map unit NnA in Harford County, Aberdeen Proving Ground, Maryland.
- Official Series Description: Nassawango(revised 11/2002), established.
- Taxonomic class: Fine-silty, mixed, semiactive, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.