Nanford soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 6 to 31 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Nanford soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Nanford spot on the map
Rated from the USDA soil survey record for Nanford silt loam, 2 to 8 percent slopes (Moore County, North Carolina) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 43% clay in the fine-earth portion.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (22.5): USDA's estimate suggests plastic behavior when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 25 in (64 cm)).
- Note Typically starts within about 6 in (15 cm) of the surface.
- Note Few rock fragments (about 14% by volume).
Layer by layer
- TopsoilAp A silt loam layer about 0 to 6 in down: about 19% clay, moderate plasticity when wet, brown when moist. Possible
- Clay subsoilBtbest layer A silty clay layer about 6 to 31 in down: about 43% clay, high plasticity when wet, yellowish red when moist. Strong lead
- Clay-rich layerBC A silty clay loam layer about 31 to 41 in down: about 35% clay, high plasticity when wet, red when moist. Strong lead
- Loamy layerC A silt loam layer about 41 to 56 in down: about 18% clay, low plasticity when wet, mottled reddish brown when moist. Weak indication
- BedrockCr Weathered bedrock about 56 to 80 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (Bt), 6 to 31 in down in the typical profile: yellowish red (5YR 5/8); friable, slightly plastic; slightly sticky. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from metavolcanics and/or argillite.
- USDA family mineralogy: kaolinitic. Kaolinite-dominated clays are typically less plastic than smectitic clays.
- USDA family particle-size class: fine.
- Drainage: well drained.
- Paralithic bedrock typically about 56 in (142 cm) down.
Where it is mapped
Seen on the map as the most common soil in 2 map units in North Carolina, in these survey areas: Moore County, North Carolina.
By state: wild clay in North Carolina.
USDA, distribution and extent: Distribution: North Carolina, South Carolina, and Virginia
USDA, geographic setting: Landscape: Piedmont uplands
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Iredell: Strong lead
- Lignum: Strong lead
- Tarrus: Strong lead
- Chewacla: Promising
- Georgeville: Promising
- Tillery: Promising
- Congaree: Possible
- Wehadkee: Possible
See it on the map
Open a Nanford spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Nanford silt loam, 2 to 8 percent slopes, map unit NaB in Moore County, North Carolina.
- Official Series Description: Nanford(revised 11/2025), established.
- Taxonomic class: Fine, kaolinitic, thermic Typic Kanhapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.