Morrison soil
Wild-clay potential
Weak indication
Weak indication: no layer of Morrison shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Morrison soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Morrison spot on the map
Rated from the USDA soil survey record for Morrison very stony sandy loam, steep (Centre County, Pennsylvania) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 25% clay. It may need settling or refining to become a clay body.
- Lowers the potential Low engineering plasticity index (5): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 39 in (99 cm)).
- Note Typically starts within about 14 in (36 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 22% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Sandy layerH1 A sandy loam layer about 0 to 14 in down: about 13% clay, moderate plasticity when wet, strong brown when moist. Weak indication
- Loamy layerH2best layer A channery sandy clay loam layer about 14 to 53 in down: about 25% clay, low plasticity when wet, strong brown when moist. Weak indication
- Sandy layerH3 A channery sandy loam layer about 53 to 74 in down: about 13% clay, low plasticity when wet, strong brown when moist. Weak indication
What it looks like raw
The loamy layer (H2), 14 to 53 in down in the typical profile: strong brown (7.5YR 5/6). Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from limestone and sandstone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 6 map units in Pennsylvania, in these survey areas: Centre County, Pennsylvania.
By state: wild clay in Pennsylvania.
USDA, distribution and extent: The valley and ridge physiographic province of Pennsylvania. The series is of moderate extent.
USDA, geographic setting: Morrison soils are on nearly level to very steep dissected upland valleys. Slopes range from 0 to 50 percent. These soils formed in residuum of weathered sandstone. The mean annual precipitation is 43 inches. Mean annual temperature is 51 degrees F., and the frost free season is 160 to 200 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Dunning: Strong lead
- Hagerstown: Strong lead
- Hublersburg: Strong lead
- Millheim: Strong lead
- Opequon: Strong lead
- Lindside: Promising
- Albrights: Possible
- Chagrin: Possible
See it on the map
Open a Morrison spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 60%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Morrison very stony sandy loam, steep, map unit MTF in Centre County, Pennsylvania.
- Official Series Description: Morrison(revised 07/2001), established.
- Taxonomic class: Fine-loamy, mixed, active, mesic Ultic Hapludalfs
- Rated with rule version 2026-09-28.1; the method is on the About page.