Matapeake soil
Wild-clay potential
Possible
Possible: a clay-enriched layer typically about 11 to 34 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Matapeake soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Matapeake spot on the map
Rated from the USDA soil survey record for Matapeake silt loam, 0 to 2 percent slopes (Kent County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 25% clay. It may need settling or refining to become a clay body.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (10).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 23 in (58 cm)).
- Note Typically starts within about 11 in (28 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilAp A silt loam layer about 0 to 5 in down: about 13% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerE A silt loam layer about 5 to 11 in down: about 13% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- Clay subsoilBtbest layer A silt loam layer about 11 to 34 in down: about 25% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Sandy layer2BC A sandy loam layer about 34 to 38 in down: about 11% clay, low plasticity when wet, strong brown when moist. Weak indication
- Sandy layer2C A loamy sand layer about 38 to 80 in down: about 7% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
What it looks like raw
The clay subsoil (Bt), 11 to 34 in down in the typical profile: yellowish brown (10YR 5/4); friable; slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: silty eolian deposits over fluviomarine sediments.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 18 map units in District of Columbia, Maryland, Virginia, in these survey areas: Baltimore County, Maryland; Cecil County, Maryland; District of Columbia; Fairfax County, Virginia; Harford County Area, Maryland; Kent County, Maryland; Prince George's County, Maryland.
By state: wild clay in District of Columbia,wild clay in Maryland,wild clay in Virginia.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Lenni: Strong lead
- Benevola: Strong lead
- Cumberstone: Strong lead
- Dunning: Strong lead
- Gunston: Strong lead
See it on the map
Open a Matapeake spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Matapeake silt loam, 0 to 2 percent slopes, map unit MnA in Kent County, Maryland.
- Official Series Description: Matapeake(revised 11/2002), established.
- Taxonomic class: Fine-silty, mixed, semiactive, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.