Lystair soil
Wild-clay potential
Weak indication
Weak indication: no layer of Lystair shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Lystair soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Lystair spot on the map
Rated from the USDA soil survey record for Lystair fine sandy loam, 0 to 15 percent slopes (Jefferson County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 46 in (116 cm)).
- Note Typically starts within about 14 in (36 cm) of the surface.
- Note Few rock fragments (about 11% by volume).
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 4 in down: about 10% clay, low plasticity when wet, dark reddish brown when moist. Weak indication
- Sandy layerH2 A fine sandy loam layer about 4 to 14 in down: about 3% clay, low plasticity when wet, reddish brown when moist. Weak indication
- Sandy layerH3best layer A loamy fine sand layer about 14 to 60 in down: about 3% clay, low plasticity when wet, olive brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 14 to 60 in down in the typical profile: olive brown (2.5Y 4/3); loose. Raw colour is not fired colour.
About the soil
- Parent material: outwash and/or till.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy over sandy or sandy-skeletal.
- Drainage: somewhat excessively drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Jefferson County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Northwestern Washington. Series is of small extent.
USDA, geographic setting: Lystair soils are on gently sloping to hilly glacial outwash plains and glacial moraine kames and kettles at elevations of near sea level to about 750 feet. The soils formed in glacial outwash or sandy glacial till. These soils are in mild marine climate that has cool, wet winters and warm dry summers. Mean January temperature is 38 degrees F., mean July temperature is 62 degrees F., and mean annual temperature is 50 degrees F. The average frost-free season is about 160 days. The mean annual precipitation ranges from 60 to 90 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Quilcene: Strong lead
- Wapato: Promising
- Kitsap: Possible
- Lummi: Possible
- Ahl: Weak indication
- Alderwood: Weak indication
- Beausite: Weak indication
- Belfast: Weak indication
See it on the map
Open a Lystair spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Lystair fine sandy loam, 0 to 15 percent slopes, map unit LyC in Jefferson County Area, Washington.
- Official Series Description: Lystair(revised 01/2000), established.
- Taxonomic class: Coarse-loamy over sandy or sandy-skeletal, isotic over mixed, mesic Vitrandic Dystroxerepts
- Rated with rule version 2026-09-28.1; the method is on the About page.