Issue soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 4 to 19 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Issue soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Issue silt loam, occasionally flooded (Charles County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 25% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (10).
- Raises the potential The official series description calls the wet soil slightly sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 15 in (38 cm)).
- Note Typically starts within about 4 in (10 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilAp A silt loam layer about 0 to 4 in down: about 15% clay, low plasticity when wet, dark yellowish brown when moist. Weak indication
- Loamy layerBwbest layer A loam layer about 4 to 19 in down: about 25% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Sandy layerBg1 A fine sandy loam layer about 19 to 30 in down: about 10% clay, low plasticity when wet, percent gray when moist. Weak indication
- Sandy layerBg2 A fine sandy loam layer about 30 to 58 in down: about 8% clay, low plasticity when wet, percent light gray when moist. Weak indication
- TopsoilAb A silt loam layer about 58 to 70 in down: about 16% clay, low plasticity when wet, dark gray when moist. Weak indication
What it looks like raw
The loamy layer (Bw), 4 to 19 in down in the typical profile: yellowish brown (10YR 5/4); silt loam; friable; slightly sticky; moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: loamy alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Maryland, in these survey areas: Baltimore County, Maryland; Charles County, Maryland; Prince George's County, Maryland.
By state: wild clay in Maryland.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Lenni: Strong lead
- Magnolia: Strong lead
- Benevola: Strong lead
- Cumberstone: Strong lead
- Howell: Strong lead
- Jackland: Strong lead
- Montalto: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Issue silt loam, occasionally flooded, map unit Is in Charles County, Maryland.
- Official Series Description: Issue(revised 11/2015), established.
- Taxonomic class: Coarse-loamy, mixed, active, mesic Fluvaquentic Dystrudepts
- Rated with rule version 2026-09-28.1; the method is on the About page.