Ingleside soil
Wild-clay potential
Weak indication
Weak indication: no layer of Ingleside shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Ingleside soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Ingleside spot on the map
Rated from the USDA soil survey record for Ingleside sandy loam, 2 to 5 percent slopes (Cecil County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 22% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (15).
- Note Thick enough to investigate (about 24 in (60 cm)).
- Lowers the potential Typically starts about 56 in (143 cm) down, deeper than most hand digging.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilAp A sandy loam layer about 0 to 10 in down: about 6% clay, low plasticity when wet, dark brown when moist. Weak indication
- Sandy layerE A sandy loam layer about 10 to 15 in down: about 6% clay, low plasticity when wet, brown when moist. Weak indication
- Clay subsoilBt A sandy loam layer about 15 to 33 in down: about 12% clay, moderate plasticity when wet, dark yellowish brown when moist. Weak indication
- Sandy layerBC A sandy loam layer about 33 to 43 in down: about 7% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerC1 A loamy sand layer about 43 to 56 in down: about 7% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Loamy layerC2best layer A silt loam layer about 56 to 80 in down: about 22% clay, moderate plasticity when wet, light yellowish brown when moist. Weak indication
What it looks like raw
The loamy layer (C2), 56 to 80 in down in the typical profile: light yellowish brown (10YR 6/4); loamy fine sand. Raw colour is not fired colour.
About the soil
- USDA family mineralogy: siliceous.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Delaware, Maryland, in these survey areas: Cecil County, Maryland; New Castle County, Delaware; Prince George's County, Maryland.
By state: wild clay in Delaware,wild clay in Maryland.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Lenni: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Howell: Strong lead
- Magnolia: Strong lead
- Talleyville: Strong lead
- Nanticoke: Promising
See it on the map
Open a Ingleside spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 75%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Ingleside sandy loam, 2 to 5 percent slopes, map unit IgB in Cecil County, Maryland.
- Official Series Description: Ingleside(revised 11/2015), established.
- Taxonomic class: Coarse-loamy, siliceous, semiactive, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.