Hann soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 27 to 38 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Hann soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Hann-McDesh-Robbscreek complex, 15 to 50 percent slopes (Ada County, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 55% clay in the fine-earth portion.
- Note USDA labels this a "Bt2" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (41): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Moderate thickness (about 11 in (28 cm)).
- Note Typically starts about 27 in (68 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 0% by volume).
- Note High shrink-swell (linear extensibility about 12.1%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- TopsoilA1 A cobbly silt loam layer about 0 to 4 in down: about 26% clay, moderate plasticity when wet, very dark grayish brown when moist. Weak indication
- TopsoilA2 A cobbly silty clay loam layer about 4 to 11 in down: about 27% clay, moderate plasticity when wet, very dark grayish brown when moist. Weak indication
- Loamy layerBA A cobbly silty clay loam layer about 11 to 20 in down: about 30% clay, high plasticity when wet, brown when moist. Possible
- Clay subsoilBt1 A silty clay layer about 20 to 27 in down: about 45% clay, high plasticity when wet, dark grayish brown when moist. Strong lead
- Clay subsoilBt2best layer A silty clay layer about 27 to 38 in down: about 55% clay, high plasticity when wet, brown when moist. Strong lead
- Clay subsoilBt3 A silty clay layer about 38 to 41 in down: about 45% clay, high plasticity when wet, brown when moist. Promising
- Clay subsoilBt4 A silty clay layer about 41 to 52 in down: about 50% clay, high plasticity when wet, yellowish brown when moist. Strong lead
- Clay subsoilBt5 A clay layer about 52 to 60 in down: about 40% clay, high plasticity when wet, light yellowish brown when moist. Promising
What it looks like raw
The clay subsoil (Bt2), 27 to 38 in down in the typical profile: brown (10YR 4/3), dark brown (10YR 3/3) moist; very hard, firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: clayey alluvium.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Idaho, in these survey areas: Ada County, Idaho; Boise County Area, Idaho, Western Part.
By state: wild clay in Idaho.
USDA, distribution and extent: West-central Idaho. MLRA 10. Hann soils are of small extent.
USDA, geographic setting: Hann soils are on fan remnants, structural benches, hill slopes, and butte escarpments at elevations of 2,600 to 5,250 feet. These soils formed in colluvium and alluvium from lacustrine deposits. Slopes range from 2 to 50 percent. The average annual precipitation is 14 to 22 inches and the average annual temperature is 45 to 51 degrees F. The frost-free period is 90 to 150 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Aradaran: Strong lead
- McDesh: Strong lead
- Shafer: Strong lead
- Aldape: Strong lead
- Bowns: Strong lead
- Breadloaf: Strong lead
- Brent: Strong lead
- Castlerock: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 35%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Hann-McDesh-Robbscreek complex, 15 to 50 percent slopes, map unit 6036 in Ada County, Idaho.
- Official Series Description: Hann(revised 12/2006), established.
- Taxonomic class: Fine, smectitic, mesic Vertic Argixerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.