Hammonton soil
Wild-clay potential
Weak indication
Weak indication: no layer of Hammonton shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Hammonton soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Hammonton spot on the map
Rated from the USDA soil survey record for Hammonton loamy sand, 0 to 5 percent slopes, Northern Coastal Plain (Salem County, New Jersey) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Note Moderate engineering plasticity index (7).
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 33 in (83 cm)).
- Note Typically starts about 47 in (120 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilAp A loamy sand layer about 0 to 5 in down: about 6% clay, low plasticity when wet, very dark grayish brown when moist. Weak indication
- Sandy layerBE A sandy loam layer about 5 to 20 in down: about 8% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Clay subsoilBt A sandy loam layer about 20 to 28 in down: about 11% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerBC A sandy loam layer about 28 to 47 in down: about 13% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerCgbest layer A loamy sand layer about 47 to 80 in down: about 10% clay, moderate plasticity when wet. Weak indication
What it looks like raw
The sandy layer (Cg), 47 to 80 in down in the typical profile: loose; nonsticky, nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: loamy fluviomarine deposits.
- USDA family mineralogy: siliceous.
- USDA family particle-size class: coarse-loamy.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in New Jersey, in these survey areas: Salem County, New Jersey.
By state: wild clay in New Jersey.
USDA, distribution and extent: Distribution--New Jersey, Delaware, and Maryland
USDA, geographic setting: Landscape: Coastal Plain upland
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Adelphia: Possible
- Mannington: Possible
- Mattapex: Possible
- Othello: Possible
- Sassafras: Possible
- Sharptown: Possible
- Swedesboro: Possible
- Woodstown: Possible
See it on the map
Open a Hammonton spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Hammonton loamy sand, 0 to 5 percent slopes, Northern Coastal Plain, map unit HbmaB in Salem County, New Jersey.
- Official Series Description: Hammonton(revised 04/2021), established.
- Taxonomic class: Coarse-loamy, siliceous, semiactive, mesic Aquic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.