Sassafras soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 9 to 32 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Sassafras soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Sassafras spot on the map
Rated from the USDA soil survey record for Sassafras fine sandy loam, 0 to 2 percent slopes (Stafford and King George Counties, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 23% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (8).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 23 in (58 cm)).
- Note Typically starts within about 9 in (23 cm) of the surface.
- Note Few rock fragments (about 3% by volume).
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 9 in down: about 8% clay, low plasticity when wet, brown when moist. Weak indication
- Loamy layerH2best layer A sandy clay loam layer about 9 to 32 in down: about 23% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Sandy layerH3 A loamy fine sand layer about 32 to 99 in down: about 8% clay, low plasticity when wet, brownish yellow when moist. Weak indication
What it looks like raw
The loamy layer (H2), 9 to 32 in down in the typical profile: yellowish brown (10YR 5/4); friable; slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: loamy marine deposits.
- USDA family mineralogy: siliceous.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 84 map units in District of Columbia, Delaware, Maryland, New Jersey, Pennsylvania, Virginia, in these survey areas: Alexandria City, Virginia; Arlington County, Virginia; Baltimore County, Maryland; Delaware County, Pennsylvania; District of Columbia; Fairfax County, Virginia; Harford County Area, Maryland; Kent County, Maryland; Salem County, New Jersey; Stafford and King George Counties, Virginia; and 4 more.
By state: wild clay in District of Columbia,wild clay in Delaware,wild clay in Maryland,wild clay in New Jersey,wild clay in Pennsylvania,wild clay in Virginia.
USDA, distribution and extent: Distribution: Delaware, District of Columbia, Maryland, New Jersey, Pennsylvania, and Virginia
USDA, geographic setting: Major Land Resource Area(S):149A, 153C, 153D
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Montalto: Strong lead
- Watchung: Strong lead
- Christiana: Strong lead
- Lunt: Strong lead
- Appling: Strong lead
- Caroline: Strong lead
- Cecil: Strong lead
- Jackland: Strong lead
See it on the map
Open a Sassafras spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Sassafras fine sandy loam, 0 to 2 percent slopes, map unit SfA in Stafford and King George Counties, Virginia.
- Official Series Description: Sassafras(revised 05/2013), established.
- Taxonomic class: Fine-loamy, siliceous, semiactive, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.