Flume soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 7 to 24 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Flume soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Flume loam, 2 to 7 percent slopes (Culpeper County, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 35% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (22): USDA's estimate suggests plastic behavior when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 17 in (43 cm)).
- Note Typically starts within about 7 in (18 cm) of the surface.
- Note Few rock fragments (about 5% by volume).
Layer by layer
- Sandy layerH1 A loam layer about 0 to 7 in down: about 15% clay, moderate plasticity when wet, light olive brown when moist. Weak indication
- Clay-rich layerH2best layer A clay loam layer about 7 to 24 in down: about 35% clay, high plasticity when wet, yellowish brown when moist. Strong lead
- Clay-rich layerH3 A clay layer about 24 to 39 in down: about 50% clay, high plasticity when wet, olive yellow when moist. Strong lead
- Clay-rich layerH4 A clay layer about 39 to 44 in down: about 45% clay, high plasticity when wet, gray when moist. Promising
- Sandy layerH5 A silt loam layer about 44 to 80 in down: about 15% clay, moderate plasticity when wet, white when moist. Weak indication
What it looks like raw
The clay-rich layer (H2), 7 to 24 in down in the typical profile: yellowish brown (10YR 5/6); firm, slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from schist and/or residuum weathered from phyllite.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Virginia, in these survey areas: Culpeper County, Virginia.
By state: wild clay in Virginia.
USDA, distribution and extent: MLRA 136 (mesic) and 148. The soils are of small extent.
USDA, geographic setting: Flume soils formed in residuum from schist, phyllite, metamonzonite and gneiss in the Northern Piedmont. Flume soils are on summits, shoulders, and backslopes of side slopes, head slopes and nose slopes of ridges. Slope gradients range from 0 to 15 percent. Mean annual air temperature 55.7 degrees F., with average winter temperature of 35.4 degrees F and average summer temperature of 74.6 degrees F. Mean annual precipitation ranges from 36.47 to 48.39 inches, frost free days range from 237 to 185 days, and elevation ranges from 100 feet to 400 feet above sea level.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Germanna: Strong lead
- Penhook: Strong lead
- Yellowbottom: Strong lead
- Elsinboro: Promising
- Happyland: Promising
- Codorus: Possible
- Blocktown: Weak indication
- Comus: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Flume loam, 2 to 7 percent slopes, map unit 24B in Culpeper County, Virginia.
- Official Series Description: Flume(revised 08/2009), established.
- Taxonomic class: Fine, mixed, semiactive, mesic Oxyaquic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.