Penhook soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 11 to 49 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Penhook soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Penhook spot on the map
Rated from the USDA soil survey record for Penhook silt loam, 2 to 7 percent slopes (Culpeper County, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 45% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (32): USDA's estimate suggests plastic behavior when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 38 in (96 cm)).
- Note Typically starts within about 11 in (28 cm) of the surface.
- Note Few rock fragments (about 10% by volume).
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- TopsoilH1 A silt loam layer about 0 to 2 in down: about 21% clay, moderate plasticity when wet. Weak indication
- Loamy layerH2 A silt loam layer about 2 to 11 in down: about 21% clay, moderate plasticity when wet, brown when moist. Possible
- Clay-rich layerH3best layer A clay layer about 11 to 49 in down: about 45% clay, high plasticity when wet, red when moist. Strong lead
- Sandy layerH4 A channery loam layer about 49 to 65 in down: about 12% clay, moderate plasticity when wet, red when moist. Weak indication
What it looks like raw
The clay-rich layer (H3), 11 to 49 in down in the typical profile: red (2.5YR 4/8); hard, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from schist and/or residuum weathered from phyllite.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 4 map units in Virginia, in these survey areas: Culpeper County, Virginia; Fauquier County, Virginia.
By state: wild clay in Virginia.
USDA, distribution and extent: Distribution: Virginia, North Carolina
USDA, geographic setting: Landscape: Piedmont uplands
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Yellowbottom: Strong lead
- Albano: Strong lead
- Appling: Strong lead
- Cecil: Strong lead
- Clover: Strong lead
- Dulles: Strong lead
- Fletcherville: Strong lead
- Flume: Strong lead
See it on the map
Open a Penhook spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 75%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Penhook silt loam, 2 to 7 percent slopes, map unit 44B in Culpeper County, Virginia.
- Official Series Description: Penhook(revised 05/2026), established.
- Taxonomic class: Fine, mixed, subactive, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.