Everett soil
Wild-clay potential
Weak indication
Weak indication: no layer of Everett shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Everett soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Everett spot on the map
Rated from the USDA soil survey record for Everett gravelly sandy loam, 0 to 15 percent slopes (Jefferson County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 44 in (111 cm)).
- Note Typically starts within about 16 in (41 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 31% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Sandy layerH1 A gravelly sandy loam layer about 0 to 6 in down: about 10% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH2 A very gravelly sandy loam layer about 6 to 16 in down: about 3% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH3best layer A very gravelly coarse sand layer about 16 to 60 in down: about 3% clay, low plasticity when wet, yellowish brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 16 to 60 in down in the typical profile: yellowish brown (10YR 5/4) dry, dark yellowish brown (10YR 4/4) moist; loose, nonsticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: glacial outwash.
- USDA family mineralogy: mixed.
- USDA family particle-size class: sandy-skeletal.
- Drainage: somewhat excessively drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Washington, in these survey areas: Jefferson County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Northwest Washington; MLRA 2; large extent
USDA, geographic setting: Elevation--10 to 280 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Quilcene: Strong lead
- Wapato: Promising
- Kitsap: Possible
- Lummi: Possible
- Ahl: Weak indication
- Alderwood: Weak indication
- Beausite: Weak indication
- Belfast: Weak indication
See it on the map
Open a Everett spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Everett gravelly sandy loam, 0 to 15 percent slopes, map unit EvC in Jefferson County Area, Washington.
- Official Series Description: Everett(revised 10/2018), established.
- Taxonomic class: Sandy-skeletal, isotic, mesic Humic Dystroxerepts
- Rated with rule version 2026-09-28.1; the method is on the About page.