Eastcan soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 28 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Eastcan soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Eastcan spot on the map
Rated from the USDA soil survey record for Eastcan loam, 0 to 3 percent slopes (Morgan Area, Utah - Morgan County and Part of Weber County) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 23% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (7.5).
- Raises the potential The official series description calls the wet soil slightly sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 32 in (81 cm)).
- Note Typically starts about 28 in (71 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 5% by volume).
- Note USDA reports about 23% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilA11, A12 A loam layer about 0 to 13 in down: about 23% clay, moderate plasticity when wet, very dark brown when moist. Weak indication
- TopsoilA13 A silt loam layer about 13 to 28 in down: about 24% clay, moderate plasticity when wet, very dark brown when moist. Possible
- Loamy layerC1, C2best layer A stratified sandy loam to clay loam layer about 28 to 60 in down: about 23% clay, moderate plasticity when wet, dark brown when moist. Possible
What it looks like raw
The loamy layer (C1, C2), 28 to 60 in down in the typical profile: dark brown (7.5YR 4/2), yellowish brown (10YR 5/4) moist; slightly hard, friable, slightly sticky and plastic. Raw colour is not fired colour.
About the soil
- Parent material: slope alluvium and/or alluvium derived from limestone, quartzite and sandstone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 4 map units in Utah, in these survey areas: Morgan Area, Utah - Morgan County and Part of Weber County.
By state: wild clay in Utah.
USDA, distribution and extent: Northern Utah and Southern Idaho. The series is inextensive.
USDA, geographic setting: Eastcan soils are at elevations of 3,000 to 5,200 feet. They occur on flood plains, stream terraces and valley bottoms. Slopes range from 0 to 10 percent. These soils formed in mixed alluvium from sandstone, quartzite and limestone. The climate is moist subhumid, with an average annual precipitation ranging from 10 to 22 inches. The mean annual temperature is 45 to 51 degrees F., and the mean summer temperature is 65 to 67 degrees F. The frost free season ranges from 100 to 140 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Ant Flat: Strong lead
- Bertag: Strong lead
- Broadhead: Strong lead
- Crooked Creek: Strong lead
- Donner: Strong lead
- Hawkins: Strong lead
- Herd: Strong lead
- Isbell: Strong lead
See it on the map
Open a Eastcan spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Eastcan loam, 0 to 3 percent slopes, map unit EaA in Morgan Area, Utah - Morgan County and Part of Weber County.
- Official Series Description: Eastcan(revised 03/2003), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Cumulic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.