Bertag soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 24 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bertag soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Bertag silt loam, 10 to 30 percent slopes (Morgan Area, Utah - Morgan County and Part of Weber County) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 38% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (32.5): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 36 in (91 cm)).
- Note Typically starts about 24 in (61 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 13% by volume).
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- TopsoilA11 A silt loam layer about 0 to 11 in down: about 21% clay, moderate plasticity when wet, very dark brown when moist. Weak indication
- TopsoilA12 A silt loam layer about 11 to 24 in down: about 21% clay, moderate plasticity when wet, very dark brown when moist. Possible
- Clay-rich layerB21tB22tB23tbest layer A silty clay loam layer about 24 to 60 in down: about 38% clay, high plasticity when wet, very dark grayish brown when moist. Strong lead
What it looks like raw
The clay-rich layer (B21tB22tB23t), 24 to 60 in down in the typical profile: very dark grayish brown (2.5Y 3/2), light grayish brown (2.5Y 5/2) dry; very hard, firm, sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: slope alluvium and/or colluvium derived from tuffaceous sandstone.
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Utah, in these survey areas: Morgan Area, Utah - Morgan County and Part of Weber County.
By state: wild clay in Utah.
USDA, distribution and extent: Bertag soils are inextensive in northern Utah; MLRA 47.
USDA, geographic setting: Landform--foothill slopes
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Ant Flat: Strong lead
- Broadhead: Strong lead
- Crooked Creek: Strong lead
- Donner: Strong lead
- Hawkins: Strong lead
- Herd: Strong lead
- Isbell: Strong lead
- Manila: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bertag silt loam, 10 to 30 percent slopes, map unit BAF in Morgan Area, Utah - Morgan County and Part of Weber County.
- Official Series Description: Bertag(revised 11/2022), established.
- Taxonomic class: Fine, smectitic, frigid Pachic Ultic Argixerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.