Dolman soil
Wild-clay potential
Weak indication
Weak indication: no layer of Dolman shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Dolman soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Dolman-Minveno-Scism complex, 0 to 8 percent slopes (Ada County, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 2% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 15 in (38 cm)).
- Note Typically starts about 45 in (114 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential Noticeable rock fragments (about 15% by volume); screening would be needed and the clay percentage applies to the fine earth only.
- Note USDA reports about 8% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilA A silt loam layer about 0 to 4 in down: about 15% clay, moderate plasticity when wet, pale brown when moist. Weak indication
- Sandy layerBA A silt loam layer about 4 to 14 in down: about 16% clay, moderate plasticity when wet, pale brown when moist. Weak indication
- Loamy layerBk A silt loam layer about 14 to 21 in down: about 18% clay, moderate plasticity when wet. Weak indication
- Sandy layer2Bkq A loam layer about 21 to 27 in down: about 14% clay, moderate plasticity when wet, light gray when moist. Weak indication
- 2Bkqm A cemented material layer about 27 to 45 in down: USDA gives no clay percentage or texture for it. Not enough data
- Sandy layer3Bkqbest layer A stratified gravel to sand layer about 45 to 60 in down: about 2% clay, low plasticity when wet, light gray when moist. Weak indication
What it looks like raw
The sandy layer (3Bkq), 45 to 60 in down in the typical profile: light gray (10YR 7/2), grayish brown (10YR 5/2) moist; very hard, firm, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: loess and/or weathered volcanic ash over loamy alluvium over sandy and gravelly alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-silty.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Idaho, in these survey areas: Ada County, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: Dolman soils are of small extent in south central and southwestern Idaho; MLRA 11.
USDA, geographic setting: Dolman soils are on old dissected terraces and on plug domes (buttes), lava flow lobes, pressure ridges and tumuli on shield volcanoes. These soils formed in silty alluvium from loess and weathered volcanic ash over loamy or sandy alluvium from igneous materials. Slopes are 1 to 15 percent. Elevations are 3,000 to 4,350 feet. The average annual precipitation is 8 to 10 inches. The average annual temperature is 47 to 53 degrees F. The frost-free season is 120 to 150 days. - terms used throughout MLRA 11 to identify the setting of this soil are quire varied although all equate to the same landscape. These will be further investigation from an MLRA project level as to the accepted terms for...
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Aldape: Strong lead
- Aradaran: Strong lead
- Bowns: Strong lead
- Breadloaf: Strong lead
- Brent: Strong lead
- Castlerock: Strong lead
- Catchell: Strong lead
- Chardoton: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 35%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Dolman-Minveno-Scism complex, 0 to 8 percent slopes, map unit 4113 in Ada County, Idaho.
- Official Series Description: Dolman(revised 05/2000), established.
- Taxonomic class: Coarse-silty, mixed, superactive, mesic Xeric Haplodurids
- Rated with rule version 2026-09-28.1; the method is on the About page.