Croy soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 10 to 18 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Croy soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Croy loam, 0 to 2 percent slopes (Davis-Weber Area, Utah) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 20% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (17.5).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Moderate thickness (about 8 in (21 cm)).
- Note Typically starts within about 10 in (25 cm) of the surface.
- Missing data Rock fragment content is not reported.
- Note USDA reports about 12% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- Sandy layerH1 A loam layer about 0 to 4 in down: about 15% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Loamy layerH2 A loam layer about 4 to 10 in down: about 21% clay, moderate plasticity when wet, brown when moist. Possible
- Loamy layerH3best layer A sandy clay loam layer about 10 to 18 in down: about 20% clay, moderate plasticity when wet, brown when moist. Possible
- Sandy layerH4 A sandy loam layer about 18 to 24 in down: about 9% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH5 A fine sand layer about 24 to 32 in down: about 4% clay, low plasticity when wet, light brownish gray when moist. Weak indication
- H6 An indurated layer about 32 to 35 in down: USDA gives no clay percentage or texture for it. Not enough data
What it looks like raw
The loamy layer (H3), 10 to 18 in down in the typical profile: brown (7.5YR 5/3), dark brown (7.5YR 3/3); slightly hard, firm, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium and/or lacustrine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Utah, in these survey areas: Davis-Weber Area, Utah.
By state: wild clay in Utah.
USDA, distribution and extent: Northern Utah. MLRA 28A. This series is of small extent.
USDA, geographic setting: Parent material: alluvium and lake sediments derived from a mixture of rocks.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Abbott: Strong lead
- Airport: Strong lead
- Eimarsh: Strong lead
- Kirkham: Strong lead
- Payson: Strong lead
- Pintailake: Strong lead
- Saltair: Strong lead
- Woods Cross: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Croy loam, 0 to 2 percent slopes, map unit Cr in Davis-Weber Area, Utah.
- Official Series Description: Croy(revised 12/2003), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Natric Durixeralfs
- Rated with rule version 2026-09-28.1; the method is on the About page.