Cleman soil
Wild-clay potential
Weak indication
Weak indication: no layer of Cleman shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Cleman soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Cleman-Beverly complex, 0 to 2 percent slopes (Ada County, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 2% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 19 in (48 cm)).
- Note Typically starts about 41 in (104 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 50% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- TopsoilAp A fine sandy loam layer about 0 to 7 in down: about 15% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- TopsoilAC A fine sandy loam layer about 7 to 10 in down: about 17% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerC1 A fine sandy loam layer about 10 to 18 in down: about 17% clay, moderate plasticity when wet, brown when moist. Weak indication
- Sandy layerC2 A fine sand layer about 18 to 29 in down: about 5% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerC3 A very fine sandy loam layer about 29 to 41 in down: about 13% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layer2C4best layer A very gravelly sand layer about 41 to 60 in down: about 2% clay, low plasticity when wet, brown when moist. Weak indication
What it looks like raw
The sandy layer (2C4), 41 to 60 in down in the typical profile: brown (10YR 5/3) dry, dark brown (10YR 3/3) moist; soft, very friable, nonsticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: coarse-loamy alluvium over sandy and gravelly alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Idaho, in these survey areas: Ada County, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: South-central Washington; MLRAs 7 and 8; small extent
USDA, geographic setting: Elevation--120 to 610 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Aldape: Strong lead
- Aradaran: Strong lead
- Bowns: Strong lead
- Breadloaf: Strong lead
- Brent: Strong lead
- Castlerock: Strong lead
- Catchell: Strong lead
- Chardoton: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 50%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Cleman-Beverly complex, 0 to 2 percent slopes, map unit 1003 in Ada County, Idaho.
- Official Series Description: Cleman(revised 09/2019), established.
- Taxonomic class: Coarse-loamy, mixed, superactive, mesic Torrifluventic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.