Biglake soil
Wild-clay potential
Weak indication
Weak indication: no layer of Biglake shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Biglake soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Biglake spot on the map
Rated from the USDA soil survey record for Riverside gravelly sandy loam, 8 to 15 percent slopes (Missoula County Area, Montana) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 5% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 44 in (111 cm)).
- Note Typically starts within about 16 in (41 cm) of the surface.
- Lowers the potential High rock content (about 62% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- TopsoilA A gravelly sandy loam layer about 0 to 9 in down: about 10% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerBw A very gravelly sandy loam layer about 9 to 16 in down: about 8% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerCbest layer An extremely gravelly loamy sand layer about 16 to 60 in down: about 5% clay, low plasticity when wet, light brownish gray when moist. Weak indication
What it looks like raw
The sandy layer (C), 16 to 60 in down in the typical profile: light brownish gray (10YR 6/2), brown (10YR 5/3) moist; loose, nonsticky, and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: sandy-skeletal.
- Drainage: excessively drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Montana, in these survey areas: Missoula County Area, Montana.
By state: wild clay in Montana.
USDA, distribution and extent: Biglake soils are of limited extent in mountain valleys in western Montana. MLRA 44A.
USDA, geographic setting: Landform- stream terraces, alluvial fans and hills.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Crow: Strong lead
- Grassvalley: Strong lead
- Half Moon: Promising
- Bignell: Possible
- Burnt Fork: Possible
- Greenough: Possible
- Minesinger: Possible
- Alberton: Weak indication
See it on the map
Open a Biglake spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Riverside gravelly sandy loam, 8 to 15 percent slopes, map unit 21 in Missoula County Area, Montana.
- Official Series Description: Biglake(revised 09/2008), established.
- Taxonomic class: Sandy-skeletal, mixed, frigid Typic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.