Wallkill soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 6 to 24 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Wallkill soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Wallkill spot on the map
Rated from the USDA soil survey record for Wallkill silt loam, 0 to 2 percent slopes (Kosciusko County, Indiana) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 20% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (13).
- Note Thick enough to investigate (about 18 in (46 cm)).
- Note Typically starts within about 6 in (15 cm) of the surface.
- Missing data Rock fragment content is not reported.
Layer by layer
- TopsoilAp A silt loam layer about 0 to 6 in down: about 20% clay, moderate plasticity when wet, very dark brown when moist. Weak indication
- Loamy layerBgbest layer A silt loam layer about 6 to 24 in down: about 20% clay, moderate plasticity when wet, grayish brown when moist. Possible
- Organic top layer2Oa An organic top layer about 24 to 79 in down, not a clay body. Weak indication
What it looks like raw
The loamy layer (Bg), 6 to 24 in down in the typical profile: grayish brown (10YR 5/2); silt loam; firm. Raw colour is not fired colour.
About the soil
- Parent material: loamy slope alluvium over herbaceous organic material.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: very poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Indiana, in these survey areas: Kosciusko County, Indiana.
By state: wild clay in Indiana.
USDA, distribution and extent: New York, New Jersey, Ohio, Indiana, Michigan, Illinois, Vermont, and Wisconsin. MLRA's 91, 95A, 95B, 97, 98, 101, 105, 110, 111, 114, 115, 139, 140, and 144A. The soil is moderately extensive.
USDA, geographic setting: Wallkill soils formed in alluvial mineral soil deposits over organic soil materials. They occur along streams that run through organic soil areas and along the margins of depressional areas adjacent to upland mineral soils. Mean annual precipitation ranges from 760 to 1270 millimeters and mean annual air temperature ranges from 7 to 13 degrees Celsius. Mean growing season ranges from 130 to 200 days in the regions of occurrence though some areas of the soil are in frost pockets.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Del Rey: Strong lead
- Saranac: Strong lead
- Toledo: Strong lead
- Aubbeenaubbee: Promising
- Crosier: Promising
- Metea: Promising
- Miami: Promising
- Rensselaer: Promising
See it on the map
Open a Wallkill spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 88%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Wallkill silt loam, 0 to 2 percent slopes, map unit Wa in Kosciusko County, Indiana.
- Official Series Description: Wallkill(revised 01/2013), established.
- Taxonomic class: Fine-loamy, mixed, superactive, nonacid, mesic Fluvaquentic Humaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.