Tombeall soil
Wild-clay potential
Possible
Possible: a surface layer with some clay typically about 7 to 28 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Tombeall soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Tombeall spot on the map
Rated from the USDA soil survey record for Tombeall silt loam, 0 to 4 percent slopes (Lewis and Nez Perce Counties, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 18% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (11).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 21 in (53 cm)).
- Note Typically starts within about 7 in (18 cm) of the surface.
- Note Few rock fragments (about 13% by volume).
- Note Surface layer; expect roots and organic matter.
Layer by layer
- TopsoilAp A silt loam layer about 0 to 7 in down: about 18% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- TopsoilAbest layer A loam layer about 7 to 28 in down: about 18% clay, moderate plasticity when wet, dark grayish brown when moist. Possible
- Sandy layerC1 A very gravelly sandy loam layer about 28 to 35 in down: about 10% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerC2 An extremely gravelly sandy loam layer about 35 to 60 in down: about 10% clay, low plasticity when wet, brown when moist. Weak indication
What it looks like raw
The topsoil (A), 7 to 28 in down in the typical profile: dark grayish brown (10YR 4/2), black (10YR 2/1) moist; slightly hard, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: mixed alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Idaho, in these survey areas: Lewis and Nez Perce Counties, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: This soil is of small extent in north central Idaho.
USDA, geographic setting: Tombeall soils are on low terraces and floodplains. Slopes range from 0 to 4 percent. These soils formed in loamy alluvium from mixed sources over gravelly alluvium from basalt. Elevations range from 800 to 1,200 feet. The average annual precipitation is 16 to 22 inches, the average annual temperature is 52 to 54 degrees F, and the frost-free period is 160 to 190 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cramont: Strong lead
- Taney: Strong lead
- Caldwell: Promising
- Latahco: Promising
- Naff: Promising
- Slickpoo: Promising
- Thatuna: Promising
- Almota: Possible
See it on the map
Open a Tombeall spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 95%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Tombeall silt loam, 0 to 4 percent slopes, map unit 137 in Lewis and Nez Perce Counties, Idaho.
- Official Series Description: Tombeall(revised 10/2002), established.
- Taxonomic class: Coarse-loamy, mixed, superactive, mesic Cumulic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.