State soil
Wild-clay potential
Promising
Promising: a clay-enriched layer typically about 15 to 34 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about State soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for State silt loam, 2 to 6 percent slopes (Randolph County, North Carolina) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 30% clay in the fine-earth portion.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (15).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 19 in (48 cm)).
- Note Typically starts within about 15 in (38 cm) of the surface.
- Note Few rock fragments (about 4% by volume).
Layer by layer
- TopsoilAp A silt loam layer about 0 to 6 in down: about 10% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerBE A silt loam layer about 6 to 15 in down: about 12% clay, low plasticity when wet, brown when moist. Weak indication
- Clay subsoilBtbest layer A sandy clay loam layer about 15 to 34 in down: about 30% clay, moderate plasticity when wet, strong brown when moist. Promising
- Sandy layerBC A fine sandy loam layer about 34 to 47 in down: about 9% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerC A sandy loam layer about 47 to 80 in down: about 9% clay, low plasticity when wet, yellowish brown when moist. Weak indication
What it looks like raw
The clay subsoil (Bt), 15 to 34 in down in the typical profile: strong brown (7.5YR 5/6); loam; friable, slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: old loamy alluvium derived from igneous and metamorphic rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Georgia, North Carolina, Virginia, in these survey areas: Douglas County, Georgia; Montgomery County, North Carolina; Prince William County, Virginia; Randolph County, North Carolina; Stafford and King George Counties, Virginia.
By state: wild clay in Georgia,wild clay in North Carolina,wild clay in Virginia.
USDA, distribution and extent: Distribution: Virginia, North Carolina, South Carolina, Alabama, and Georgia
USDA, geographic setting: Landscape: Piedmont and coastal river valleys
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Cecil: Strong lead
- Badin: Strong lead
- Caroline: Strong lead
- Davidson: Strong lead
- Helena: Strong lead
- Mecklenburg: Strong lead
- Susquehanna: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 95%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for State silt loam, 2 to 6 percent slopes, map unit StB in Randolph County, North Carolina.
- Official Series Description: State(revised 10/2008), established.
- Taxonomic class: Fine-loamy, mixed, semiactive, thermic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.