Shamel soil
Wild-clay potential
Weak indication
Weak indication: no layer of Shamel shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Shamel soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Shamel sandy loam, 30 to 60 percent slopes (Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil slightly sticky and nonplastic.
- Note Thick enough to investigate (about 22 in (56 cm)).
- Note Typically starts about 38 in (96 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential Noticeable rock fragments (about 28% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Sandy layerH1 A sandy loam layer about 0 to 11 in down: about 8% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerH2 A loam layer about 11 to 17 in down: about 10% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH3 A loam layer about 17 to 38 in down: about 10% clay, low plasticity when wet, pale brown when moist. Weak indication
- Sandy layerH4best layer A gravelly sandy loam layer about 38 to 60 in down: about 10% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
What it looks like raw
The sandy layer (H4), 38 to 60 in down in the typical profile: light yellowish brown (10YR 6/4), dark yellowish brown (10YR 4/4) moist; slightly hard, firm, slightly sticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: loess and volcanic ash mixed with colluvium derived from gneiss and schist.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Washington, in these survey areas: Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
By state: wild clay in Washington.
USDA, distribution and extent: North-central Washington and east slopes of the Cascade Mountains. Series is of small extent.
USDA, geographic setting: Shamel soils are on mountains and mostly have a north or west exposure. Elevations range from 1,400 to 3,800 feet. The soils formed in colluvial deposits of weathered gneiss, and schist, mixed with loess and volcanic ash. The climate has warm, dry summers and cold, moist winters. Average annual precipitation is 16 to 20 inches. The average January temperature is about 23 degrees F., the average July temperature is about 66 degrees F., and the average annual air temperature is 44 degrees F. The growing season at 28 degrees F., is 135 to 170 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Cle Elum: Promising
- Cowiche: Possible
- Dragoon: Possible
- Georgecreek: Possible
- Kingmont: Possible
- Loneridge: Possible
- Morical: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Shamel sandy loam, 30 to 60 percent slopes, map unit 270 in Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
- Official Series Description: Shamel(revised 10/2002), established.
- Taxonomic class: Coarse-loamy, mixed, superactive, frigid Ultic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.