Poplar Forest soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 8 to 25 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Poplar Forest soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Poplar Forest spot on the map
Rated from the USDA soil survey record for Poplar Forest fine sandy loam, 15 to 45 percent slopes (Forsyth County, North Carolina) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 40% clay in the fine-earth portion.
- Note USDA labels this a "Bt1" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (20): USDA's estimate suggests plastic behavior when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 17 in (44 cm)).
- Note Typically starts within about 8 in (20 cm) of the surface.
- Note Few rock fragments (about 8% by volume).
Layer by layer
- TopsoilAp A sandy loam layer about 0 to 3 in down: about 10% clay, low plasticity when wet, reddish brown when moist. Weak indication
- Sandy layerE A sandy loam layer about 3 to 8 in down: about 9% clay, low plasticity when wet, reddish brown when moist. Weak indication
- Clay subsoilBt1best layer A clay layer about 8 to 25 in down: about 40% clay, high plasticity when wet, red when moist. Strong lead
- Clay subsoilBt2 A clay loam layer about 25 to 31 in down: about 35% clay, moderate plasticity when wet, red when moist. Promising
- Sandy layerC A sandy loam layer about 31 to 80 in down: about 13% clay, moderate plasticity when wet, dark brown when moist. Weak indication
What it looks like raw
The clay subsoil (Bt1), 8 to 25 in down in the typical profile: red (2.5YR 4/6); friable; slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from mica schist and/or other micaceous metamorphic rock.
- USDA family mineralogy: kaolinitic. Kaolinite-dominated clays are typically less plastic than smectitic clays.
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 7 map units in North Carolina, in these survey areas: Forsyth County, North Carolina.
By state: wild clay in North Carolina.
USDA, distribution and extent: Distribution: Virginia and North Carolina
USDA, geographic setting: Landscape: Piedmont upland
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Banister: Strong lead
- Casville: Strong lead
- Cecil: Strong lead
- Clifford: Strong lead
- Enon: Strong lead
- Fairview: Strong lead
- Hiwassee: Strong lead
See it on the map
Open a Poplar Forest spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Poplar Forest fine sandy loam, 15 to 45 percent slopes, map unit PoF in Forsyth County, North Carolina.
- Official Series Description: Poplar Forest(revised 04/2026), established.
- Taxonomic class: Fine, kaolinitic, mesic Typic Kanhapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.