Banister soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 18 to 50 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Banister soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Banister spot on the map
Rated from the USDA soil survey record for Banister fine sandy loam, 0 to 6 percent slopes, rarely flooded (Forsyth County, North Carolina) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 48% clay in the fine-earth portion.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (28): USDA's estimate suggests plastic behavior when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 32 in (81 cm)).
- Note Typically starts within about 18 in (46 cm) of the surface.
- Note Few rock fragments (about 8% by volume).
Layer by layer
- TopsoilAp A fine sandy loam layer about 0 to 6 in down: about 12% clay, low plasticity when wet, olive brown when moist. Weak indication
- Sandy layerE A fine sandy loam layer about 6 to 10 in down: about 12% clay, low plasticity when wet, olive brown when moist. Weak indication
- Loamy layerBE A clay loam layer about 10 to 18 in down: about 27% clay, moderate plasticity when wet, olive brown when moist. Possible
- Clay subsoilBtbest layer A clay layer about 18 to 50 in down: about 48% clay, high plasticity when wet, yellowish brown when moist. Strong lead
- Loamy layerC A sandy clay loam layer about 50 to 80 in down: about 25% clay, low plasticity when wet, light gray when moist. Weak indication
What it looks like raw
The clay subsoil (Bt), 18 to 50 in down in the typical profile: yellowish brown (10YR 5/6); firm, slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: old clayey alluvium derived from igneous and metamorphic rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in North Carolina, in these survey areas: Forsyth County, North Carolina.
By state: wild clay in North Carolina.
USDA, distribution and extent: Distribution: Virginia and North Carolina
USDA, geographic setting: Landscape: Piedmont
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Casville: Strong lead
- Cecil: Strong lead
- Clifford: Strong lead
- Enon: Strong lead
- Fairview: Strong lead
- Hiwassee: Strong lead
- Jackland: Strong lead
See it on the map
Open a Banister spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Banister fine sandy loam, 0 to 6 percent slopes, rarely flooded, map unit BaB in Forsyth County, North Carolina.
- Official Series Description: Banister(revised 04/2026), established.
- Taxonomic class: Fine, mixed, active, mesic Aquic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.