Penn soil
Wild-clay potential
Weak indication
Weak indication: no layer of Penn shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Penn soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Penn channery silt loam, 3 to 8 percent slopes (Lebanon County, Pennsylvania) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 17% clay.
- Note Moderate engineering plasticity index (11).
- Note The official series description calls the wet soil nonsticky and slightly plastic.
- Note Moderate thickness (about 10 in (25 cm)).
- Note Typically starts within about 0 in (0 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 20% by volume); screening would be needed and the clay percentage applies to the fine earth only.
- Note Surface layer; expect roots and organic matter.
Layer by layer
- TopsoilApbest layer A channery silt loam layer about 0 to 10 in down: about 17% clay, moderate plasticity when wet, dark reddish brown when moist. Weak indication
- Clay subsoilBt1 A channery silt loam layer about 10 to 15 in down: about 23% clay, moderate plasticity when wet, reddish brown when moist. Weak indication
- Clay subsoilBt2 A channery silt loam layer about 15 to 19 in down: about 25% clay, moderate plasticity when wet, reddish brown when moist. Weak indication
- Clay subsoilBt3 A channery loam layer about 19 to 22 in down: about 21% clay, moderate plasticity when wet, dark reddish brown when moist. Weak indication
- Sandy layerC A very channery loam layer about 22 to 28 in down: about 18% clay, moderate plasticity when wet, weak red when moist. Weak indication
- BedrockR Bedrock about 28 to 38 in down: no clay layer to dig. Weak indication
What it looks like raw
The topsoil (Ap), 0 to 10 in down in the typical profile: dark reddish brown (5YR 3/3); silt loam; friable, nonsticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from shale and siltstone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
- Lithic bedrock typically about 28 in (71 cm) down.
Where it is mapped
Seen on the map as the most common soil in 42 map units in Pennsylvania, Virginia, in these survey areas: Berks County, Pennsylvania; Bucks County, Pennsylvania; Chester County, Pennsylvania; Fauquier County, Virginia; Lebanon County, Pennsylvania; Lehigh County, Pennsylvania; Montgomery County, Pennsylvania.
By state: wild clay in Pennsylvania,wild clay in Virginia.
USDA, distribution and extent: Southeastern Pennsylvania, New Jersey, Maryland and Virginia. The series is of large extent.
USDA, geographic setting: Penn soils are on nearly level to steep moderately dissected uplands. Slopes range from 0 to 60 percent. They formed in materials weathered from noncalcareous reddish shale, siltstone, and fine-grained sandstone, normally of Triassic age. The climate is humid temperature. Mean annual precipitation ranges from 38 to 48 inches, mean annual air temperature ranges from 50 to 59 degrees F, and the frost free season ranges from 170 to 200 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Watchung: Strong lead
- Hagerstown: Strong lead
- Albano: Strong lead
- Appling: Strong lead
- Cecil: Strong lead
- Clover: Strong lead
- Dulles: Strong lead
- Fletcherville: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Penn channery silt loam, 3 to 8 percent slopes, map unit PeB in Lebanon County, Pennsylvania.
- Official Series Description: Penn(revised 02/2016), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Ultic Hapludalfs
- Rated with rule version 2026-09-28.1; the method is on the About page.